background image

9x6 Cabana - Bevel 

Assembly Manual 

(Metal Roof)

 

Some of the safety and usage measures you may wish to consider include: 

 
-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the 
snow off the roof(s).  
-if the product is elevated, any structural and building code requirements are solely the customer's  
responsibility, and should be abided by.  
-in high or gusty wind conditions it is advisable to keep the structure securely grounded.  
-have a regular maintenance plan to ensure screws, doors, windows and parts are tight.  

 
Customer agrees to hold Outdoor Living Today Partnership and any Authorized Dealers free 
of any liability for improper installation, maintenance and repair.

Version #4 

May 26, 2020

1-888-658-1658                        www.outdoorlivingtoday.com            [email protected]

Page 1

In the event of a missing or broken piece, simply call the Outdoor Living Today Customer Support Line  
@ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our commitment to you to courier  
replacement parts, free of charge, within 10 business days of this notification. Replacement parts will not be  
provided free of charge after the 30 day grace period. 

 
Safety Points and Other Considerations 
Our products are built for use based on 
proper installation and normal residential 
use, on level ground. Please follow the  
instruction manual when building your  
shed and retain the manual for future  
maintenance purposes.

Note:  The General Assembly Manual 
illustrates a Door Configuration in the 
front center location. The Door can also 
be positioned in the front corners. To 
correctly configure Door in front  
corners, follow general assembly steps 
and refer to Page 39 for required 
changes.

Thank you for purchasing 
a 9x6 Cabana. Please take 
the time to identify all the 
parts prior to assembly. 

Summary of Contents for 9x6 Cabana Bevel









































Reviews: