background image

1. General information for the user

1.1 Preliminary instructions/proper use

The present recycling and recharging unit for A/C systems is meant for commercial purposes and is thought
to be used by trained personnel only being aware of the principles of refrigeration, conscious of the hazards
which may derive from equipment working under pressure with substances at very low boiling temperature.

We advise to read the present instruction manual carefully and to strictly comply with the given
information,   paying   particular   attention   to   the   safety   regulations.   We   shall   decline   any
responsibility resulting from the improper use of the equipment, use for purposes other than
those described in the present operating manual, incorrect operation, damages resulting from
external influences.

Always keep the unit in vertical position

 in order to avoid oil leaks and the compressor to be damaged.

1.2 General safety regulations 

Read

 the instructions for use careful before starting to operate with this Aircon service unit;

Follow 

the informations and the instructions

 of the refrigerant manufacturer;

Observe 

any instructions on servicing vehicle aircon systems which apply at your company;

Use 

with 

R134a

 refrigerant  indicated on the data plate (R-134a for Fast20X/Ecos20X; HFO-1234YF

for Fast20XYF);

Do not

 make modifications to the service unit;

Only employ original spare parts

 and accessories;

Use

 authorized additives or consumables only(ask for advice from an authorized reseller);

Before   starting

  the   machine   first  

check   each   time  

whether   the   charging   hoses   and   the   quick

couplers are undamaged and are not leaking; 

Recover

 refrigerant from the hoses before releasing the quick connections;

Do not

 leave the unit unattended when switched on; Use the main switch to switch off the unit after

its use;

Always 

wear

 personal safety equipment ( 

gloves

 and protective 

goggles)

;

Avoid inhaling

 the refrigerating gas;

Avoid the contact

 with the skin by refrigerating gas, danger of freezing;

Never abandon

 the refrigerating gas 

in the environment

;

Do not use

 the unit in potentially 

explosive environments

; (for instance: battery charging rooms);

Do not smoke

 whilst using the recharging unit;

During the operations, l

ocate the unit on a flat

 and leveled surface;

Do not use

 the unit 

near flames

 or sources of heat; at high temperatures the refrigerating gas can

generate poisonous substances for inhalation;

Do not use

 the unit i

n very humid and wet environments

 or in the rain;

Use

 the unit in 

airy environments

;

During maintenance operations 

disconnect the unit from the electrical power

.

Avoid removing the connecting hoses  

if not necessary; in case always make a vacuum in the

hoses before using again;

Ecos-150  sw  1.x.x  - ver. 1.0            

    

Page 3/20

Summary of Contents for ECOS-150





















Reviews: