OKOndt GROUP Eddycon C Operating Manual Download Page 56 | Manualshive

Page: 56 / 62

OKOndt GROUP Eddycon C Operating Manual Download Page 56

56

Figure 41

9.4.4

Battery pack mounting is carried out strictly in reverse order.

10

TYPICAL FAILURES AND TROUBLESHOOTING

10.1

The list of the most common and probable failures is given in

Table 9.

Table 9 –

Typical failures and troubleshooting

Failure

Probable cause

Remedy

When pressing

"

Power

"

key, the screen is not

lightened

The storage battery is

discharged

Charge the storage

battery

When the instrument is

switched On, the

inscription

"

Storage

battery needs charging

"

is displayed

The storage battery is

discharged

Charge the storage

battery

ATTENTION!

THE FLAW DETECTOR MUST BE SWITCHED OFF

WHEN  NON-TYPICAL  IMAGES  APPEAR  ON  THE  FLAW  DETECTOR  SCREEN
AND  SOFTWARE  PROGRAMS  BUZZ.  IF  REPEATED  SWITCHING  ON  OF  THE
FLAW DETECTOR (NOT EARLIER THAN IN 3 MINUTES) DOES NOT LEAD TO
THE  RESETTING  OF  NORMAL  OPERATION,  THE  FLAW  DETECTOR  SHOULD
BE  SENT  TO  THE  MANUFACTURER  FOR  REPAIR  OR  IT  IS  NECESSARY  TO
ADDRESS THE SERVICE CENTER.

1

«
...
54
55
56
57
58
...
»

Summary of Contents for Eddycon C































































Reviews:

No comments