Ohyama woozoo IPE-1221G, User Manual, Page: 11 / 120

7
EN EN
NOTE
NOTE
Introduction for buttons on
remote control
MODE
COOL DRY
SWING
TIMER
● This is a general use remote control. It could be
used for the air conditioner with multifunction.
For the functions which the model doesn't have,
if press the corresponding button on the remote
control, the unit will keep the original running
status.
● When power is connected (stand by condition),
you can operate the air conditioner through the
remote control.
● When unit is on, each time you press the button
on remote control, the sending signal icon " "
on the display of remote control will blink once. If
the air conditioner gives out a beep sound, it
means the signal has been sent.
● When unit is off, set termperature will be
displayed on the remote control (lf the light of
indoor unit display is turned on, the correspond -
ing icon will bedisplayed); When unit is on, it will
display the icon of the on-going function.
● Under Auto speed, air conditioner will select
proper fan speed automatically according to
ambient temperature.
● Fan speed can't be adjusted under dry mode.
● When unit is on, press this button to set Timer
Off. T-OFF and H icon will be blinking. Within 5s,
● Heat (IPE-1221GH Model only ) : when
selecting heat mode, air conditioner will operate
under heat mode. Then press “+” or ”- “ button
to adjust set temperature. Press Fan button to
adjust fan speed. (Cooling only unit can't
receive heating mode signal. lf set heat mode
by remote control, press ON/OFF button can't
turn on the air conditioner.)
● Pressing “+”or “-” button once will increase or
decrease set temperature by 1°F(°C). Hold “+”
or “-” button for 2s, set temperature on rermote
controller will change quickly. Release the
button after your required set temperature is
reached. (Temperature can't be adjusted under
auto mode)
● When setting Timer On or Timer Off, press “+”
or “-” button to adjust the time. (See TIMER
Button for setting details)
Pressing this button can select fan speed
circularly as: AUTO, SPEED 1( ), SPEED 2( ),
SPEED 3( ), SPEED 4 ( ).
Press this button to turn on up & down air swing.
Under Cool, Heat and Dry mode, press this button
to turn on Sleep function. Press this button to
cancel Sleep function. Under Fan and Auto mode,
this function is unavailable.
( IPE-1221GH Model only )
● Auto
：
when selecting auto mode, air conditioner
will operate automatically according to ambient
temperature. Set temperature can't be adjusted
and won't be displayed either. Press Fan button
to adjust fan speed.
● Cool
：
when selecting cool mode, air conditioner
will operate under cool mode. Then press” + “or”
-” button to adjust set temperature. Press Fan
button to adjust fan speed.
● Dry: when selecting dry mode, air conditioner will
operate at low fan speed under dry mode. In dry
mode, fan speed can't be adjusted.
● Fan: when selecting fan mode, air conditioner will
operate in fan mode only. Then press Fan button
to adjust fan speed.
Press this button to turn unit ON/OFF.
Pressing this button once can select your required
mode circularly as below (the corresponding icon" "
will be lit up after the mode is selected):
button
button
button
button
NOTICE
Replacement of batteries in
remote control
battery
remove
reinstall
Cover of battery box
press “+” or “-” button to adjust the time for Timer
Off. Pressing “+” or “-” button once will increase or
decrease the time by 0.5h. Hold “+” or “-” button
for 2s, time will change quickly. Release the
button after your required set time is reached.
Then press TIMER button to confirm it. T-OFF and
Hicon will stop blinking.
● When unit is off, press this button to set Timer On.
T-ON and H icon will be blinking. Within 5s, press
“+” or “-” button to adjust the time for Timer On.
Pressing “+” or “-” button once will increase or
decrease the time by 0.5h. Hold “+” or “-” button
for 2s, time will change quickly. Release the
button after your required set time is reached.
Then press TIMER button to confirm it.T-ON and
Hicon will stop blinking.
● Cancel Timer On/off: If Timer function is set up,
press TIMER button once to review the remaining
time. Within 5s, press TIMER button again to
cancel this function.
Function introduction for
combination buttons
Child lock function
Light function
Temperature display switchover function
NOTE
Press "+" and "-" buttons simultaneously can turn on
or turn off child lock function. When child lock
function is started up, child lock indicator on remote
control is ON. lf you operate the remote control,
remote control won't send signal.
1. Press the back side of remote control on the
spot marked with " ", and then push out the
cover of battery box along the arrow direction.
2. Replace two 7# (AAA 1.5V) dry batteries and
make sure the positions of “+” and “-” polar are
correct.
3. Reinstall the cover of battery box.
Under switch-on or switch-off state, you may hold
"+" and "FAN" buttons simultaneously for 3 seconds
to set the lamp on or off and send the code. After
being energized the lamp is defaulted on.
Under OFF status, press "-" button and "MODE"
button simultaneously can switch between °C and °F.
● Range of time setting is: 0.5~24h.
● The interval between two motions can't exceed 5s,
otherwise the remote control will exit setting status.
● During operation, point the remote control signal
sender at the receiving window on indoor unit.
● The distance between signal sender and receiving
window should be no more than 8m, and there should
be no obstacles between them.
● Signal may be interfered easily in the room where
there is fluorescent lamp or wireless telephone;
remote control should be close to indoor unit during
operation.
● Replace new batteries of the same model when
replacement is required.
● When you don't use remote control for a long time,
please take out the batteries.
● lf the display on remote control is fuzzy or there's no
display, please replace batteries.