O2matic HOT 100 End User Manual Download | Manualshive

Page: 21 / 30

background image

D 8.4.1.10

21

4

Maintenance and Support

This section contains important information regarding safely maintaining the device.
This device does not need to be calibrated.

4.1

Cleaning

Warning

Disconnect the AC power adaptor from the device before cleaning it. Do not clean
device in any other manner than described in this user manual.

Warning

If the HOT device is malfunctioning or does not provide the correct treatment,
please contact your service provider.

Use wet towel or cloth with either water or alcohol. Dry off surfaces with a dry towel or
cloth afterwards. The device should be thoroughly cleaned once a week.

Important:

Make sure that there are no dust or lint in the air input or air output.

4.2

Trademark

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc.

«
...
19
20
21
22
23
...
»

Summary of Contents for HOT 100































Reviews:

No comments

Related manuals for HOT 100

Brand: MacDon Pages: 17

Brand: Olympus Pages: 50

Brand: VAHVA Pages: 19

Brand: GALLERY Pages: 18

Brand: Oberheim Pages: 40

Brand: Baoding Longer Precision Pump Pages: 6

Brand: Cambro Pages: 6

Brand: IDEAL Networks Pages: 10

Varycolor MICRO 150HTI

Brand: JB-Lighting Pages: 18

Brand: Haas Pages: 12

Brand: SaMASZ Pages: 25

Brand: RAB Pages: 4

Brand: ASIA TECHNOLOGY Pages: 38

TEMSTM POCKET 7.3

Brand: ASCOM Pages: 8

Brand: Chamberlain Pages: 8

Brand: LINET Pages: 25

Brand: MD SPORTS Pages: 12

Brand: SurgiVet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands