background image

DESCRIPTION

nVent RAYCHEM RayClic-S Splice Kit
nVent RAYCHEM RayClic-T Tee and End Seal Kit
nVent RAYCHEM RayClic-X Cross and End Seal Kit

These kits are for use with nVent RAYCHEM IceStop, XL-Trace 

and HWAT heating cables. The connection is designed to 

be strapped to the pipe, or wall mounted. These installation 

instructions should be used in conjunction with the IceStop, 

XL-Trace, and HWAT System Installation and Operation Manuals. 

For  technical support, contact your nVent representative or call 

nVent (800) 545-6258.

TOOLS REQUIRED

•  TORX T20 screw driver

•  Utility knife

•  Wire cutters

OPTIONAL ACCESSORIES  

(NOT INCLUDED IN THIS KIT)

•  RayClic-SB-02 Wall mounting bracket
•  RayClic-SB-04 Pipe mounting bracket

This component is an electrical device that 

must be installed correctly to ensure proper 

operation and to prevent shock or fire. Read 

these important warnings and carefully follow 

all the installation instructions.
•  To minimize the danger of fire from 

sustained electrical arcing if the heating 

cable is damaged or improperly installed, 

and to comply with the requirements of 

nVent, agency certifications, and national 

electrical codes, ground-fault equipment 

protection must be used. Arcing may not be 

stopped by conventional circuit breakers.

•  Bus wires will short if they contact each 

other. Keep bus wires separated.

•  Keep components and heating cable ends 

dry before and during installation.

•  The black heating cable core is conductive 

and can short. It must be properly insulated 

and kept dry.

•  Component approvals and performance are 

based on the use of nVent-specified parts 

only. Do not use substitute parts or vinyl 

electrical tape.

•  Leave these instructions with end user for 

reference and future use.

WARNING:

APPROVALS

For HWAT, IceStop, and XL-Trace only

Hazardous Locations: For IceStop (GM-XT) only

Class I, Div. 2, Groups A,B,C,D

718K Pipe Heating Cable

877Z De-Icing and Snow Melting

Not UL Listed with XL-Trace heating cable 

for buried piping.

APPROVED

-w

RayClic Connection System

Installation Instructions

Summary of Contents for Raychem RayClic Series











Reviews: