manualshive.com logo in svg

NSK Megatorque PS Series, User Manual

Share
Download
NSK Megatorque PS Series User Manual Download Page 98

— 6-10 — 

6.3.2. Program Positioning Operation 

 

The program positioning operation means an execution of some preprogrammed positioning 
commands and operational conditions in the program channels. The inputs of PRG0 to PRG7 
specify a program channel and the input RUN (Start program) starts the positioning operation. 

◊ 

The program operation is available via RS-232C communication. 

 

The commands and parameters related to positioning operations are listed in the Table 6-5.   
Refer to “9. Details of Commands and Parameters” for more details. 

Table 6-6: Inputs/Outputs and parameters related to program positioning.   

Category 

Name 

(code) 

Function  

Initial 

setting 

Data range 

Unit

RUN 

Start program 

– 

Turning ON from OFF starts positioning. .   

– 

PRG0 to 7 

Internal program channel 
selection  

– 

Specifies the program channel by ON and OFF 
(binary combination)   

– 

Cont

rol 

Input 

STP 

Stops positioning 
operation. 

– 

OFF: Positioning permitted 
ON: Starts decelerating and inhibits positioning 
operation.  

– 

BUSY 

In-operation – 

Open: Idle   
Closed: Executing positioning.   

– 

Cont

rol 

Output 

IPOS 

In-position – 

Open: Positioning unfinished. Lost target 

position.  

Closed: Positioning completed. Target position 
secured.  

– 

FW 

IPOS output mode 

–1.0

– 0.1 to – 10 000.0:  CFIN mode 

0.0: IPOS mode 

0.1 to 10 000.0:  FIN mode 

ms 

– 

ms 

BW 

BUSY signal stability 
timer 

0.0

0.0 to 10 000.0

ms 

MD 

Deceleration select 

0.0

0.0: Applies the deceleration value specified in 

the program being executed. 

0.1 to 800.0

– 

s

-2

 

Param

e

ter  

OE 

Sequence code 

0

0: Completes a positioning after the completion of channel 

program that is currently being executed.   

1: After completion of channel program that is currently 

executed, the input RUN executes the program of the 
channel with the next channel number. (Disregards the 
input PRG.)   

2: Automatically executes the program of the channel with 

the next channel number after completion of the 
channel program that is currently executed. 

 

Besides the positioning commands, rotational velocity and acceleration, it is possible to program 
almost all parameters including servo gains and conditions for completing positioning.   
These functions make possible to have optimal tuning that is suited for each positioning 
operation.  

 

The contents of program are simple. It consists of the settings of parameter and positioning 
commands and they will be sequentially executed from the beginning. Figure 6-5 below 
illustrates an example of a program.   

Summary of Contents for Megatorque PS Series



















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands