manualshive.com logo in svg

NSK Megatorque PS Series, User Manual

Share
Download
NSK Megatorque PS Series User Manual Download Page 267

— 9-43 — 

P   

KB: Kill Brake 

 

This parameter terminates the dynamic brake function.   

◊ 

Refer to “8.4.1. Preparation for Teaching” for details.   

 

This is to decrease rotational resistance when turning the rotor manually in case of teaching 
operation.  

 

Category Parameter 

 

(The EEPROM does not back up the setting of this parameter.   

Format 

KB data 

 

0 

: Dynamic brake effective   

Data range 

1 

: Dynamic brake ineffective 

Shipping set 

0 

 

 

When the servo is turned off because of an alarm, the dynamic brake function is always effective 
regardless of the setting of parameter KB. 

P   

LB: Observer Limiter 

 

When the input IOFF (Integration OFF) is activated, this parameter limits the observer output to a 
specified percentage.   

◊ 

Refer to “8.2.3. Integration OFF: IOFF” and “8.5.1. Servo Block Diagram” for details.   

 

When the observer output is set to 0%, the effect of integral control is nullified, thus cancelling 
settling motion to the target position.   

 

Category Parameter 

 

Format 

LB data 

 

Data range 

0.00 to 100.00% 

 

Shipping set 

0.00 

 

P   

LG: Lower Gain (When the input IOFF is ON) 

 

This parameter lowers the position loop proportional gain to a specified percent when the input 
IOFF (Integration OFF) is ON.   

◊ 

Refer to “8.2.3. Integration off: IOFF” and “8.5.1. Servo Block Diagram” for details.   

 

Category Parameter 

 

Format 

LG data 

 

Data range 

0.00 to 100.00% 

 

Shipping set 

50.00 

 

 

Summary of Contents for Megatorque PS Series



















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands