NRI G-26.4000 Series Manual Download Page 50

Page: 50 / 96

Manual G-26.4000:

Page 50

National Rejectors, Inc. GmbH, Germany

Function 19 = Communication with a Card System

G-26.4000 Standard and G-26.4800 Professional

Attention: A ‘1’ may only be programmed, if a credit card system is connected to the changer.

When you connect a GLOBO Card system, please refer to the installation instructions for the
GLOBO Card system.

Action

Key

Display

* Select function

F until

19 appears

* Display setting

* Change setting

* Return to base function

* Programme new setting

P or +

shuts down

Note: 0 = no card system available

1 = card system connected

The fault code 33 appears, if

- the card system is switched off
- the connecting cable is defective
- no card system is available, however, a ‘1’ is programmed

The display shuts down after approximately 2 minutes. The changer no longer attemps to
communicate with the card system and the fault code is recorded.

The communication with the card system can be reestablished as follows:

* Key F

fault code --33-- appears

* Key F again

display shuts down and card system responds again

Communication Card System

Summary of Contents for G-26.4000 Series

































































































Search results

Summary of Contents for G-26.4000 Series

Reviews:

Related manuals for G-26.4000 Series

Brands by name

Popular brands

NRI G-26.4000 Series, Manual

Search results

Summary of Contents for G-26.4000 Series

Reviews:

Related manuals for G-26.4000 Series

Brands by name

Popular brands