NRI G-26.4000 Series Manual Download Page 12

Page: 12 / 96

Manual G-26.4000:

National Rejectors, Inc. GmbH, Germany

Page 12

NRI Programming Unit

NRI offers a programming station by which you can change the settings according to your
requirements.

By using the NRI programming station for validators series G-10.4000/5 you can

- check the proper function of the connected validator,

- if necessary, determine the reason for a fault

- change the programming

- display the actual measured values of an inserted coin

- programme the coin channels by inserting special coins

- change the validator setting in order to adapt it to the desired vending machine.

A programming station for the G-10.4000/5 includes the following units:

G-55.0287 adapter (for AT computers) with 9-pin plug
or
G-55.288 adapter (for XT computers) with 25-pin plug
G-19.0577 tester
G-19.0584 test stand
93 00 631 software 'KUNEMP', deliverable on 5.25" or 3.5" disk

The software 'KUNEMP' can also be used for the validator series G-18.3000.

You can connect the NRI programming station to an IBM personal computer or compatible with
a RS232 interface.

G-10.4000/5

Summary of Contents for G-26.4000 Series

































































































Search results

Summary of Contents for G-26.4000 Series

Reviews:

Related manuals for G-26.4000 Series

Brands by name

Popular brands

NRI G-26.4000 Series, Manual

Search results

Summary of Contents for G-26.4000 Series

Reviews:

Related manuals for G-26.4000 Series

Brands by name

Popular brands