manualshive.com logo in svg

NRI G-26.4000 Series, Manual

Share
Download
NRI G-26.4000 Series Manual Download Page 13

Manual G-26.4000:

Page 13

National Rejectors, Inc. GmbH, Germany

4.  Transport and Connection of Unit

Transport

o Before transport please empty all tubes
o Transport and storage in factory packing prevents damage
o No transit fixings required

Attention

Components behind validator are at line voltage.

Always

 unplug changer 

before

 removing validator.

Always 

refit the safety screw.

Prior to installation

* Check that changer is correct for your machine
* Check operating voltage and change if necessary (switch S1 on interface module)

(Only units for 110.. 240 Volts).

Installation

o Connecting cable to vendor must not yet be plugged
* Mount changer
* Unfasten safety screw (see figure)

* Remove validator
* Secure changer with screws
* Refit validator
* Fix safety screw
*  Connect non-fused green/yellow earth lead
* Plug to machine
* Check that motors are in standby state (key ‘+’ twice)
* Fill change tubes with at least 20 coins each (see ‘Filling Change Tubes’ page  18)

Transport/Connection

Summary of Contents for G-26.4000 Series

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands