manualshive.com logo in svg

Northern N3NVR Series, User Manual

Share
Download
Northern N3NVR Series User Manual Download Page 5

Network Security Advice 

Network Video Recorder 

User Manual 

 

Issue: V4.6.X(2022-04-24) 

 

v 

6.  Only forward the ports that must be used 

Only forward the network ports that must be used. Avoid forwarding a long port area. Do not set 

the device's IP to DMZ. 

If the camera is connected locally to the NVR, you do not need to forward the port for each 

camera. Only the ports of the NVR need to be forwarded. 

7.  Use a different username and password on the video surveillance system. 

In the unlikely event that your social media account, bank, email, etc. account information is 

leaked, the person who obtained the account information will not be able to invade your video 

surveillance system. 

8.  Restrict the permissions of the ordinary account 

If your system is serving multiple users, make sure that each user has permission to access only 

its permissions. 

 

 

 UPNP 

When the UPnP protocol is enabled, the router will automatically map the intranet ports. 

Functionally, this is user-friendly, but it causes the system to automatically forward the data of 

the corresponding port, causing the data that should be restricted to be stolen by others. 

If you have manually opened HTTP and TCP port mappings on your router, we strongly 

recommend that you turn this feature off. In actual usage scenarios, we strongly recommend that 

you do not turn this feature on. 

 

SNMP 

If you do not use the SNMP, we strongly recommend that you turn it off. The SNMP function is 

limited to temporary use for testing purposes. 

 

Multicast 

Multicast technology is suitable for the technical means of transmitting video data in multiple 

video storage devices. There have been no known vulnerabilities involving multicast technology 

so far, but if you are not using this feature, we recommend that you turn off multicast playback 

on your network. 

 

Summary of Contents for N3NVR Series



























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands