Northern N3NVR Series User Manual Download Page 12

Page: 12 / 218

Network Video Recorder
User Manual

Safety instructions

xii

Issue: V4.6.X(2022-04-24)

Safety instructions

The following are the correct use of the product. In order to prevent danger and prevent property

damage, please read this manual carefully before using the device and strictly comply that when

using it. Please save the manual after reading.

Requirements



The front-end devices of POE are required to be installed indoors.



The NVR device does not support wall mounting.



Do not place and install the device in direct sunlight or near heat-generating equipment.



Do not install the device in a place subject to high humidity, dust or soot.



Please keep the equipment installed horizontally or install the equipment in a stable place,

taking care to prevent the product from falling.



Do not drop or spill liquid into the device and ensure that no liquid-filled items are placed

on the device to prevent liquid from flowing into the device.



Install the device in a well-ventilated area, and do not block the ventilation openings of the

device.



Use the device only within the rated input and output range.



Do not disassemble the device at will.



Please transport, use and store the device within the permissible humidity and temperature

range.

Power Requirement



Be sure to use the specified manufacturer's model battery, otherwise there is a danger of

explosion!



Be sure to use the battery as required, otherwise there is a danger of the battery catching

fire, exploding or burning!



Only use the same model of battery when replacing the battery!



Be sure to dispose of the used battery as the instruction of battery!



Be sure to use the power adapter that meets standard with the device, otherwise the

personal injury or equipment damage caused by the user will be borne by the user.

Summary of Contents for N3NVR Series



























































































































































































































Search results

Summary of Contents for N3NVR Series

Reviews:

Brands by name

Popular brands

Northern N3NVR Series, User Manual

Search results

Summary of Contents for N3NVR Series

Reviews:

Brands by name

Popular brands