Northern N2NVR Series User Manual Download Page 22

Page: 22 / 167

Digital Video Recorder
User Manual

Issue: V4.3 (2020-05-09)



We are not liable for any video data loss caused by improper installation,

configuration, operation, and hard disk errors.



All images in the document are for reference only, please subject to the actual

products.

2.3

About This User Manual

Please note the following points before using this user manual:



This user manual is intended for persons who operate and use the DVR.



The information in this user manual applies to the full series DVR, DVR as an

example for description.



Read this user manual carefully before using the DVR and follow the methods

described in this manual when using the DVR.



If you have any doubts when using the DVR, contact your product seller.



In the case of product upgrade, the information in this document is subject to

change without notice.

2.4

Installation Environment and Precautions

Installation environment

Table 2-3 defines the installation environment of the DVR.

Table 2-3

Installation environment

Item

Description

Electromagnetism

The DVR conform to national standards of electromagnetic

radiation and does not cause harm to the human body.

Temperature

–10

C to +45

Humidity

20% to 80%

Atmospheric pressure 86 Kpa to 106 Kpa

Power supply

DC 12V, 2A / DC 12V, 4A, please refer to actual product.

Power consumption

<15W (excluding the hard disk)

Installation precautions

Note the following points when installing and operating the DVR:



Install the DVR horizontally.

Summary of Contents for N2NVR Series








































































































































































Search results

Summary of Contents for N2NVR Series

Reviews:

Related manuals for N2NVR Series

Brands by name

Popular brands

Northern N2NVR Series, User Manual

Search results

Summary of Contents for N2NVR Series

Reviews:

Related manuals for N2NVR Series

Brands by name

Popular brands