manualshive.com logo in svg

North Atlantic 75DS2, Operation Manual

Share
Download
North Atlantic 75DS2 Operation Manual Download Page 27

 

  

DLV Two/Four Channel (Module 5*) 

  

75DS2 Operations Manual

 

North Atlantic Industries, Inc.

 

11/11/2011

 

Rev: 2011-11-11-1000 

www.naii.com

 

Page 27 of 43 

 

DLV Status, BIT Test 

Check the corresponding bit of the 

DLV BIT Test Status Register

 for status of BIT (Test-Accuracy) Testing for 

each active channel. 

A ”1” means Accuracy Failed; “0” means Accuracy OK. Accuracy defaulted to 0.2% FS 

output as compared to commanded position. Channels that are inactive are also set to “0”. The status bits will be 
set to indicate an accuracy (0.2% FS) problem and the results can be read from 

DLV Status Registers 

within 2 

seconds and if enabled, an interrupt will be generated (See 

Interrupt Register)

. 

This test continuously sequences between the channels on the card with each output being measured for 
approximately 180mSec.  If the measured position has an error greater the 0.2% FS, a flag will be set in the 
appropriate register.  If the input position is stepped more then 0.2% FS during a test cycle, the test cycle will not 
generally indicate an error. Any DLV test status failure, transient or intermittent, will latch the 

DLV Test Status 

Register.

  Reading will unlatch register. 

 

D15 

D14 

D13 

D12 

D11 

D10 

D9 

D8 

D7 

D6 

D5 

D4 

D3 

D2 

D1 

D0 

DLV Status, BIT Test 

X 

X

 

X

 

X

 

X

 

X

 

X 

X

 

X

 

X

 

X

 

X

 

X

 

X

 

CH2 

CH1 

Excitation Loss Interrupt Enable 

Set the bit to enable interrupts for the corresponding channel.  When enabled, an excitation input loss (DLV 
Status, Excitation) will trigger an interrupt. Default is “0” to disable interrupt on all channels. When Status Interrupt 
is enabled, Status Interrupt is reported through the 

Excitation Loss Interrupt

 Vector. 

 

D15 

D14 

D13 

D12 

D11 

D10 

D9 

D8 

D7 

D6 

D5 

D4 

D3 

D2 

D1 

D0 

Excitation Loss Interrupt Enable 

X 

X

 

X

 

X

 

X

 

X

 

X 

X

 

X

 

X

 

X

 

X

 

X

 

X

 

CH2 

CH1 

Signal Loss Interrupt Enable 

Set the bit to enable interrupts for the corresponding channel. When enabled, a signal input loss (DLV Status, 
Signal Loss) will trigger an interrupt. Default is “0” to disable interrupt on all channels. When Status Interrupt is 
enabled, Status Interrupt is reported through the 

Signal Loss Interrupt

 Vector. 

 

D15 

D14 

D13 

D12 

D11 

D10 

D9 

D8 

D7 

D6 

D5 

D4 

D3 

D2 

D1 

D0 

Signal Loss Interrupt Enable 

X 

X

 

X

 

X

 

X

 

X

 

X 

X

 

X

 

X

 

X

 

X

 

X

 

X

 

CH2 

CH1 

BIT Test Fail Interrupt Enable 

Set the bit to enable interrupts for the corresponding channel.  When enabled, a BIT Test Failure (DLV Status, 
BIT Test) will trigger an interrupt. Default is “0” to disable interrupt on all channels. When Status Interrupt is 
enabled, Status Interrupt is reported through the 

BIT Test Loss Interrupt 

Vector. 

 

D15 

D14 

D13 

D12 

D11 

D10 

D9 

D8 

D7 

D6 

D5 

D4 

D3 

D2 

D1 

D0 

BIT Test Fail Interrupt Enable 

X 

X

 

X

 

X

 

X

 

X

 

X 

X

 

X

 

X

 

X

 

X

 

X

 

X

 

CH2 

CH1 

Phase Lock Loss Interrupt Enable 

Set the bit to enable interrupts for the corresponding channel. When enabled, a Phase Lock Loss (DLV Status, 
Phase Lock Loss) will trigger an interrupt. Default is “0” to disable interrupt on all channels. When Status Interrupt 
is enabled, Status Interrupt is reported through the 

Phase Lock Loss Interrupt 

Vector. 

 

D15 

D14 

D13 

D12 

D11 

D10 

D9 

D8 

D7 

D6 

D5 

D4 

D3 

D2 

D1 

D0 

Phase Lock Loss Interrupt Enable 

X 

X

 

X

 

X

 

X

 

X

 

X 

X

 

X

 

X

 

X

 

X

 

X

 

X

 

CH2 

CH1 

Summary of Contents for 75DS2












































Reviews:

No comments

Brands by name

Popular brands

Load more brands