Nortel 2750 Page 48 Installation Manual Download

Page: 48 / 108

Chapter 2 Cabling the VPN Router and turning the power on

NN46110-318 02.01

T1/E1 CSU/DSU WAN interface card LEDs

Figure 16

shows the LEDs on the T1/E1 CSU/DSU WAN interface card.

Figure 16

LEDs on the T1/E1 CSU/DSU WAN interface card

Table 12

describes the LEDs on the T1/E1 CSU/DSU WAN interface card.

Table 12

LED indicators on the T1/E1 CSU/DSU WAN interface card

LED

Indicator

Description

LED 1

Red

The red alarm LED is lit when a loss-of-signal (LOS) or

out-of-frame (OOF) condition is detected on the receive

signal.

LED 2

Blue

The blue alarm LED is lit when receiving an upstream

failure denoted by an alarm indication signal (AIS).

LED 3

Yellow

The yellow alarm LED is lit when the far-end equipment

is in the red alarm condition.

LED 4

Green

The green LED is lit when the condition is normal

operation.

CS160012A

LED 4, Green

LED 3, Yellow

LED 1, Red

LED 2, Blue

Summary of Contents for 2750













































































































Search results

Summary of Contents for 2750

Reviews:

Related manuals for 2750

Brands by name

Popular brands

Nortel 2750, Installation Manual

Search results

Summary of Contents for 2750

Reviews:

Related manuals for 2750

Brands by name

Popular brands