Nortel 2750 Page 43 Installation Manual Download

Page: 43 / 108

Chapter 2 Cabling the VPN Router and turning the power on

Nortel VPN Router Installation — VPN Router 2750

1000BASE-T (1000 GT) Ethernet interface card LEDs

The following figure shows the LEDs on the 10BASE-T/100BASE-TX/
1000BASE-T 1000 GT Ethernet interface card.

Figure 11

LEDs on the 1000 GT Ethernet interface card

The following table describes the LEDs on the 1000 GT Ethernet interface card.

1000BASE-T (1000 MT) Ethernet interface card LEDs

Figure 12

shows the LEDs on the 1000BASE-T Ethernet interface card.

Table 7

LED indicators on the 1000 GT Ethernet interface card

LED

Indicator

Description

ACT/LINK

Steady green

The port is connected to a valid link partner.

Flashing green

The card is sending or receiving network data. The

frequency of the flashes increases with increased

traffic.

Off

The card is not sending or receiving data.

10/100/1000

Yellow

The port is operating at 1000 Mb/s.

Green

The port is operating at 100 Mb/s.

Off

The port is operating at 10 Mb/s.

Summary of Contents for 2750













































































































Search results

Summary of Contents for 2750

Reviews:

Related manuals for 2750

Brands by name

Popular brands

Nortel 2750, Installation Manual

Search results

Summary of Contents for 2750

Reviews:

Related manuals for 2750

Brands by name

Popular brands