Nortel 2750 Page 44 Installation Manual Download

Page: 44 / 108

Chapter 2 Cabling the VPN Router and turning the power on

NN46110-318 02.01

Figure 12

LEDs on the 1000BASE-T (1000 MT) Ethernet interface card

Table 8

describes the LEDs on the 1000BASE-T Ethernet interface card.

1000BASE-SX Ethernet interface card LED

Figure 13

shows the LED on the 1000BASE-SX Ethernet interface card.

Figure 13

LED on the 1000BASE-SX Ethernet interface card

Table 8

LED indicators on the 1000BASE-T (1000 MT) Ethernet interface card

LED

Indicator

Description

ACT/LNK

Steady green

The port is connected to a valid link partner.

Flashing green

The LAN port is sending or receiving network data.

Off

The port is not linked to a valid partner.

10/100/1000

Off

The LAN port is operating at 10 Mb/s.

Green

The LAN port is operating at 100 Mb/s.

Orange

The LAN port is operating at 1000 Mb/s.

11287EA

10 = OFF

100 = GRN

1000 = ORG

CT/LNK

Intel PR

10/100/1000

ACT/LNK

11288EA

CT/LNK

Intel PR

ACT/LNK

Summary of Contents for 2750













































































































Search results

Summary of Contents for 2750

Reviews:

Related manuals for 2750

Brands by name

Popular brands

Nortel 2750, Installation Manual

Search results

Summary of Contents for 2750

Reviews:

Related manuals for 2750

Brands by name

Popular brands