Nortel 2750 Page 47 Installation Manual Download

Page: 47 / 108

Chapter 2 Cabling the VPN Router and turning the power on

Nortel VPN Router Installation — VPN Router 2750

ADSL WAN interface card LEDs

Figure 15

shows the LEDs on the asymmetric digital subscriber line (ADSL)

WAN interface card.

Figure 15

LEDs on the ADSL WAN interface card

Table 11

describes the LEDs on the ADSL WAN interface card.

Table 11

LED indicators on the ADSL WAN interface card

CONN LED

Tx/Rx LED

Description

Steady green

The ADSL interface card is not initialized; the

software driver is not installed.

Off

The ADSL interface card is initialized, but has not

established a link with the ADSL network.

Flashing green

Off

The ADSL interface card is attempting to establish a

link with the ADSL network.

Steady green

Off

The ADSL interface card has established a link with

the ADSL network.

Steady green

Flashing green

The ADSL interface card is sending or receiving

network data. (The LED can be dim.)

LED

RX/TX LED

ADSL

RX/TX

Summary of Contents for 2750













































































































Search results

Summary of Contents for 2750

Reviews:

Related manuals for 2750

Brands by name

Popular brands

Nortel 2750, Installation Manual

Search results

Summary of Contents for 2750

Reviews:

Related manuals for 2750

Brands by name

Popular brands