manualshive.com logo in svg

Nortel 2340, Installation Manual

Share
Download
Nortel 2340 Installation Manual Download Page 60

60

NN47250-306 (324121-A Version 01.01)

Electromagnetic Compatibility Notices

FCC (USA)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  (1) this 
device may not cause harmful interference, and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of 
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures:

VCCI Marking (Class 
A)

Japan

BSMI Certification 
Number & Class A 
Warning

Taiwan

GOST R Marking

Russia

RRL MIC Mark

Korea

China Compulsory 
Certification Mark

China

Table 9: Table 10. Product Certification Markings

 

Summary of Contents for 2340

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands