manualshive.com logo in svg

Nortel 2340, Installation Manual

Share
Download
Nortel 2340 Installation Manual Download Page 56

56

Troubleshooting

NN47250-306 (324121-A Version 01.01)

Memory Size Increased

Memory size has increased since the last boot. If no memory was 
added, there may be a problem with the system.

Memory Size Changed

Memory size has changed since the last boot. If no memory was 
added or removed, then memory may be bad.

No Boot Device Available

System did not find a device to boot.

Off Board Parity Error

A parity error occurred on an off-board card. This error is 
followed by an address.

On Board Parity Error

A parity error occurred in onboard memory. This error is 
followed by an address.

Parity Error

A parity error occurred in onboard memory at an unknown 
address.

NVRAM / CMOS / PASSWORD 
cleared by Jumper

NVRAM, CMOS, and passwords have been cleared. The system 
should be powered down and the jumper removed.

<CTRL_N> Pressed

CMOS is ignored and NVRAM is cleared. User must enter Setup.

Table 8: BIOS Error Messages (Sheet 2 of 2)

Error Message

Explanation

Summary of Contents for 2340

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands