manualshive.com logo in svg

Nortel 2340, Installation Manual

Share
Download
Nortel 2340 Installation Manual Download Page 33

33

Nortel WLAN — Location Engine 2340 Installation

Software Installation of WLAN 
Location Engine 2340

Network requirements

For the proper operation of LE, following are the network requirements:

•

It should be connected to the wired backbone and should have a statically assigned IP address.

•

Each sensor must be assigned a static IP address.

•

It must be able to access the wire-side interface of the sensors and a configuration client through the 
following connections:

Rack Installation

For illustrated instructions, see 

“L-Bracket Mount Kit Installation Instructions” on page 30 

chapter in this manual

.

Table 6: Connections to access WLE2340

Source Device

Source Port

Destination 
Device

Destination 
Port

Purpose

Appliance

any, (*)

Sensors

UDP 37008

Communication

Sensors

UDP 37008

Appliance

any, (*)

Communication

Configuration 
Client

any, (*)

Appliance

TCP 443

HTTPS

Configuration 
Client (admin)

any, (*)

Appliance

TCP 8003

HTTPS

Note.  

Use the hardware supplied with your specific rack if it is different from the hardware 

supplied in this kit.

Summary of Contents for 2340

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands