Nortel 2340 Installation Manual Download Page 57

Page: 57 / 64

Nortel WLAN — Location Engine 2340 Installation

Regulatory and Certification Information

Product Regulatory Compliance

Product Safety Compliance

The IP network server complies with the following safety requirements:

•

UL60950-1 /CSA 60950-1 (USA / Canada)

•

EN60950-1 (Europe)

•

IEC60950-1 (International), CB Certificate & Report including all international deviations

•

GS Certificate (Germany)

•

GOST R Approval (Russia)

•

CE - Low Voltage Directive 73/23/EEE (Europe)

•

CCC Certification (China)

•

BSMI CNS 13436 (Taiwan)

Product EMC Compliance - Class A Compliance

The IP network server has been has been tested and verified to comply with the following electromagnetic compatibility
(EMC) regulations.

•

FCC /ICES-003 - Emissions (USA/Canada)

•

CISPR 22 - Emissions (International)

•

EN55022 - Emissions (Europe)

•

EN55024 - Immunity (Europe)

•

EN61000-3-2 - Harmonics (Europe)

•

EN61000-3-3 - Voltage Flicker (Europe)

•

CE- EMC Directive 89/336/EEC (Europe)

•

VCCI Emissions (Japan)

•

AS/NZS: CISPR 22 Emissions (Australia / New Zealand)

•

BSMI CNS13438 Emissions (Taiwan)

•

GOST R Approval Emissions and Immunity (Russia)

Note.

The WLE2340 hardware is based on the

Intel NSW1U-R Server

all regulatory

compliance testing was done by Intel

Summary of Contents for 2340

































































Search results

Summary of Contents for 2340

Reviews:

Brands by name

Popular brands

Nortel 2340, Installation Manual

Search results

Summary of Contents for 2340

Reviews:

Brands by name

Popular brands