manualshive.com logo in svg

Nortel 1750, Install Manual

Share
Download
Nortel 1750 Install Manual Download Page 95

Appendix A  Technical specifications  

95

Nortel VPN Router Installation — VPN Router 1750 

Table 30

 provides the T1/E1 CSU/DSU cable pinouts for a straight-through 

connection.

Quad T1/E1 CSU/DSU WAN interface card

The quad T1/E1 CSU/DSU WAN interface card has four connectors that provide 
the signals needed to interface to T1 or E1 equipment. 

Figure 41

 shows the quad 

T1/E1 CSU/DSU WAN interface card.

Figure 41   

Quad T1/E1 CSU/DSU WAN interface card

Each connector on the quad T1/E1 CSU/DSU WAN interface card accommodates 
an 8-pin RJ-48 modular patch cord. These cables are commonly sold as Category 
5, or Ethernet, cables.

Table 30   

T1/E1 CSU/DSU cable pinouts for straight-through connection

Nortel termination

Remote termination

Signal

Pin # to Pin #

Signal

Receive A (RXDA)

1

1

Receive A (RXDA)

Receive B (RXDB)

2

2

Receive B (RXDB)

not used

3

3

not used

Transmit B (TXDB)

4

4

Transmit B (TXDB)

Transmit A (TXDA)

5

5

Transmit A (TXDA)

not used

6

6

not used

not used

7

7

not used

not used

8

8

not used

Note: 

Nortel does not supply cables with the quad T1/E1 CSU/DSU 

interface card.

CS160012A

Summary of Contents for 1750













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands