manualshive.com logo in svg

Nortel 1750, Install Manual

Share
Download
Nortel 1750 Install Manual Download Page 35

Chapter 1  Cabling the VPN Router and turning the power on  

35

Nortel VPN Router Installation — VPN Router 1750 

56/64K CSU/DSU WAN interface card LEDs

Figure 8

 shows the LEDs on the 56/64K CSU/DSU WAN interface card.

Figure 8   

LEDs on the 56/64K CSU/DSU WAN interface card

Table 9

 describes the LEDs on the 56/64K CSU/DSU WAN interface card.

Table 9   

LED indicators on the 56/64K CSU/DSU WAN interface card

LED

Description

Blue

The blue alarm LED is lit when the interface card detects a DDS 

out-of-frame (OOF) condition on the receive signal.

Red

The red alarm LED is lit when the interface card detects a DDS loss-of- 

signal (LOS) or loss-of-frame (LOF) condition on the receive signal.

Yellow

The yellow alarm LED is lit when the interface card detects a DDS 

out-of-service condition on the receive signal. (This LED indicates that 

the far-end equipment detects a local LOS or LOF condition.)

Green

The green LED is lit when the interface card receives valid DDS signal 

and framing (this LED indicates normal operation of the card.)

All LEDs off

The port is disabled.

56/64K

DDS

Blue LED 

Yellow LED 

Red LED

Green LED

Summary of Contents for 1750













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands