manualshive.com logo in svg

Nortel 1750, Install Manual

Share
Download
Nortel 1750 Install Manual Download Page 87

Appendix A  Technical specifications  

87

Nortel VPN Router Installation — VPN Router 1750 

1000BASE-SX Ethernet interface card

The 1000BASE-SX Ethernet interface card implements short-wavelength 

 

(850 nm) laser transmissions. Use this interface card to connect to fiber Gigabit 
Ethernet interfaces on other devices in your network, as well as to provide 
increased throughput. The 1000BASE-SX Ethernet interface card has a single 
type LC fiber connector.

Figure 35 

shows the 1000BASE-SX Ethernet interface card.

Figure 35   

1000BASE-SX Ethernet interface card

The port on the 1000BASE-SX Ethernet interface card accommodates a 
multimode fiber (MMF) cable that meets MMF standards. Select fiber cable for 
this interface as follows:

•

50-micron MMF cable: provides a distance range of 500–550 meters (m)

•

62.5-micron MMF cable: provides a distance range of 220–275 m

You can order a 10-foot MMF cable from Nortel: 

•

Order no. DM0011117 provides an LC-to-LC connector

•

Order no. DM0011118 provides an LC-to-SC connector

11288EA

A

CT/L

N

K

Intel PR

O

R

Summary of Contents for 1750













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands