manualshive.com logo in svg

Nortel 1750, Install Manual

Share
Download
Nortel 1750 Install Manual Download Page 82

82

  Appendix A  Technical specifications

NN46110-316 02.01

Figure 31   

SSL VPN Module 1000

The SSL VPN Module 1000 has no external access: all traffic to and from the SSL 
VPN Module 1000 card occurs over an internal high-speed link.

The SSL VPN Module 1000 is supported on VPN Router 5000, 2700, and 1750 
gateways running VPN Router Version 5.0 software. You must install the SSL 
VPN Module 1000 in slot 1 of the VPN Router 5000, 2700, or 1750.

The VPN Router gateway distinguishes between the services that it provides and 
the services that the SSL VPN Module 1000 provides and immediately forwards 
the appropriate traffic to the SSL VPN module.

Note: 

For complete information about the SSL VPN Module 1000 and 

instructions for configuring it, see 

Nortel VPN Router Configuration — 

SSL VPN Services 

(NN46110-501).

11356EA

Online

Utilization

1

Activity

2   -

Summary of Contents for 1750













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands