Nortel 1750 Install Manual Download Page 84

Page: 84 / 108

Appendix A Technical specifications

NN46110-316 02.01

The following figure shows the 1000BASE-T (1000 GT) Ethernet interface
full-height card for VPN Router.

Figure 33

1000BASE-T (1000 GT) Ethernet interface card

Select cables for the card as follows. Keep in mind that this card is
auto-negotiating and uses the highest possible data rate:

•

For 1000BASE-T operation, use Category 5 four-pair Ethernet wiring. The
cable must comply with the TIA 568 wiring specification. Nortel recommends
a maximum length of 100 meters for the cable segment.

•

For 100BASE-TX operation, use Category 5 twisted-pair wiring: one pair
each for transmit and receive operations. The cable must comply with the

EIA 568 wiring specification. Nortel recommends a maximum length of 100
meters for the cable segment.

•

For 10BASE-T operation, use Category 3, 4, or 5 twisted-pair wiring.

The following table provides the pinouts for the 1000BASE-T (1000 GT) Ethernet
interface card..

Table 21

1000BASE-T (1000 GT) Ethernet pinouts

Pin

Description

TP0+

TP0-

TP1+

TP2+

TP2-

TP1-

TP3+

TP3-

CS260010A

12345678

Summary of Contents for 1750













































































































Search results

Summary of Contents for 1750

Reviews:

Brands by name

Popular brands

Nortel 1750, Install Manual

Search results

Summary of Contents for 1750

Reviews:

Brands by name

Popular brands