manualshive.com logo in svg

Nortel 1750, Install Manual

Share
Download
Nortel 1750 Install Manual Download Page 70

70

  Chapter 4  Configuring the management IP interface

NN46110-316 02.01

The serial main menu appears.

Main Menu: System is currently in NORMAL mode.

0) Management Address

1) Interfaces

2) Administrator

3) Default Private Route Menu

4) Default Public Route Menu

5) Create A User Control Tunnel (IPsec) Profile

6) Restricted Management Mode

FALSE

7) Allow HTTP Management

TRUE

8) Firewall Options

9) Shutdown

B) System Boot Options

P) Configure Serial Port

C) Controlled Crash

L) Command Line Interface

R) Reset System to Factory Defaults

E) Exit, Save and Invoke Changes

Please select a menu choice (0 - 9,B,P,C,L,R,E):

5

To configure the Interface IP address from the serial menu, type 

1

, and press 

Enter

.

The interface menu appears.

- Interface Menu

0) Slot 0, Port 2, Public LAN

IP Address =

Subnet Mask = 0.0.0.0

Speed/Duplex = AutoNegotiate

1) Slot 0, Port 1, Private LAN

IP Address =192.167.120.14

Subnet Mask = 255.255.255.0

Speed/Duplex = AutoNegotiate

R) Return to the Main Menu.

Please select a menu choice:

Summary of Contents for 1750













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands