14
N60-5
6
CHEEK PAD ASSEMBLY
6.1 Insert the rear flap of the comfort padding of the left cheek pad into the cavity
between the rear seal and the inner polystyrene shell (Fig.7).
6.2 Insert the chin strap into the cavity in the cheek padding and press at the three
snap fasteners placed on the back to hook it in the relevant housing (Fig.6).
6.3 Repeat the same process with the right cheek padding.
Warning:
the buttons are hooked on only when you hear the click. Make sure that the
strap is coming out well from the cheek padding.
WARNING
-
If your helmet is equipped with the double D-Ring retention system, pull it
down as indicated in the attached double D-Ring label.
-
Remove the inner comfort padding only when cleaning or washing is required.
-
Never use the helmet without having completely and correctly reassembled its
inner comfort padding and its cheek pads with expanded foam.
-
Delicately hand-wash in lukewarm water (max. 30° C) and neutral soap.
-
Rinse with cold water and dry at room temperature, away from direct sunlight.
-
Never machine-wash the inner comfort padding.
-
The inner polystyrene is an easily deformable material. It is apt to change or get
partially destroyed to help absorb shocks.
-
Do not modify or alter the helmet’s internal polystyrene components in any way.
-
Clean the inner polystyrene components with a damp cloth only and allow it to dry
at room temperature away from direct sunlight.
-
Never use tools or equipment of any sort to carry out the steps described above.
EYEWEAR ADAPTIVE
1
CREATING SPACE FOR THE EYEWEAR
1.1 Remove the left cheek pad from the helmet (see instructions above).
1.2 Unhook the eyelet “A” on the rear frame of the corresponding cheek pad at the
upper press stud on the back (Fig.12).
1.3 Remove the upper flap “B” of the frame from the loop on the back of the frame
itself (Fig.12).
1.4 Gently remove the inner expanded foam padding from the fabric lining cover of the
cheek pad (Fig.13).
1.5 Detach the upper part of the pre-lined inner padding (Fig.13), then correctly repo-
sition the remaining part of the padding in the cheek pad.
It is recommended that you keep the removed padding for reuse in the
future.
1.6 Insert the upper flap “B” of the frame into the loop on the back of the cheek pad
and reattached the eyelet “A” at the top press stud on the back (Fig.12).
1.7 Remove the left cheek pad from the helmet (see instructions above).
1.8 Repeat the same process with the right cheek padding.
1.3 Remove the rear flap of the comfort padding on the left side from the cavity be-
tween the rear seal and the inner polystyrene shell; then completely remove the
cheek padding from the helmet (Fig.7).
1.4 Repeat the same process on the right side of the helmet.
2
DISASSEMBLY OF INNER EXPANDED FOAM CHEEK PADDING
To make it even easier to wash the parts of the inner comfort padding, the cheek pads
on the helmet come with internal padding in expanded foam that can be removed from
the fabric lining cover. To remove this padding, proceed as follows after removing the
cheek pads from the helmet (see instructions above).
2.1 Unhook the three eyelets “A” of the rear frame on the left cheek pad at the three
press studs (top, front and rear) on the back (Fig.8).
2.2 Remove the upper flap “B” and lower flap “C” of the frame from the respective
loops on the back of the frame itself (Fig.8).
2.3 Gently remove the inner expanded foam padding from the fabric lining cover of the
cheek pad (Fig.9).
2.4 Repeat the same process with the right cheek padding.
3
LINER DISASSEMBLY
3.1 Release the rear left flap of the liner from the rear edge of the shell by gently pulling
the comfort padding towards the inside (Fig.10). Then repeat the process also with
the rear right flap.
3.2 Grasp the front left area of the liner and pull it upwards to remove the relative flap
from the support fixed to the inner polystyrene shell (Fig.11).
Then repeat this process also for the centre and right forehead flaps.
3.3 Completely remove the liner from the helmet.
4
LINER ASSEMBLY
4.1 Correctly insert the liner into the helmet, lying it carefully on the bottom.
4.2 Insert the front left flap of the liner into the corresponding housing in the support
fixed to the polystyrene inner shell and push it downwards until it locks completely.
Then repeat this process also for the centre flap and the right flap (Fig.11).
4.3 Insert the right and left rear flaps of the liner in their respective housing on the
edge of the shell (Fig.10). Push the flaps until they are completely hooked to the
support.
5
ASSEMBLY OF INNER EXPANDED FOAM CHEEK PADDING
5.1 Gently insert the inner expanded foam padding into the left cheek pad fabric lining
cover (Fig.9). Carefully spread out the padding, checking that there are no wrinkles
in the cheek pad fabric cover
5.2 Remove the upper flap “B” and lower flap “C” of the frame in respective loops on
the back of the frame itself (Fig.8).
5.3 Unhook the three eyelets “A” of the rear frame on the left cheek pad at the three
press studs (top, front and rear) on the back (Fig.8).
5.4 Repeat the same process with the right cheek padding.
INSTRUCTIONS FOR USE
Summary of Contents for N60-5
