Nolan N60-5, Safety And Instructions For Use

Page: 12 / 80

12
N60-5
INSTRUCTIONS FOR USE
VISOR
1
DISASSEMBLY
1.1 Open the visor completely.
1.2 Press and hold the visor release button (A) down and slide the visor forward until
it clicks (Fig.1).
1.3 Free the visor fastenings (B1 and B2) from their housing (Fig.2).
1.4 Follow the same steps on the other side of the helmet.
2 ASSEMBLY
2.1 Set the visor in open position by placing the visor fastenings (B1 and B2) in line
with the housings in the visor mechanism (Fig.2).
2.2 Insert fastening B1 into the provided housing and press the visor against the shell
in line with fastening B2. This will push the visor release button (A).
2.3 Slide the visor backwards until the visor release button (A) clicks.
2.4 Follow the same steps on the other side of the helmet.
2.5 Close the visor completely.
WARNING
- Make sure that the mechanisms are working properly. Open and close the visor,
making sure that the mechanisms hold it in the different positions. If necessary,
repeat the above-mentioned steps.
- Do not use the helmet if the visor has not been assembled properly.
- Do not remove the side mechanisms from the shell.
- Should any of the side mechanisms fail or be damaged, please contact a Nolan-
group authorized dealer.
(Available as standard or accessory/spare part)
1 INNER VISOR PINLOCK
®
ASSEMBLY
1.1 Disassemble the visor (see instructions above).
1.2 Make sure that the inner surface of the visor is clean and check that the pin adjust-
ment external levers are turned inwards (Fig.3).
1.3 Put the PINLOCK ® inner visor onto the visor.
The silicone-sealed profile of the PINLOCK
®
inner visor should be in contact
with the inner surface of the visor.
1.4 Insert one side of the PINLOCK ® inner visor on one of the two visor pins and hold
it in position (Fig.4).
1.5 Widen the visor and fasten the other side of the PINLOCK
®
inner visor to the sec-
ond pin (Fig.5).
1.6 Release the visor.
1.7 Remove the protective film from the PINLOCK
®
inner visor and check that the
entire silicone-sealed profile of the inner visor adheres to the visor.
1.8 Fit the visor on the helmet - as per instructions above.
2 CHECKING AND ADJUSTING THE PINLOCK ® INNER VISOR STRETCH
Check the correct PINLOCK ® inner visor assembly by opening and closing the visor
and make sure that they do not move.
If the PINLOCK
®
inner visor is not tightly fixed to the visor, move gradually both external
adjust-ment levers upwards to stretch (Fig.3).
The maximum stretch is achieved when the pin adjustment external levers are turned
outwards.
WARNING
- The presence of dust between the two visors may scratch both surfaces.
- Scratched PINLOCK
®
visors and inner visors may reduce visibility and should
therefore be replaced.
- Regularly check the correct stretch of the PINLOCK ® inner visor to prevent it from
moving and scratching both surfaces.
- If the helmet visor fogs up and/or condensation forms between the visors, check
that the PINLOCK
®
inner visor is both correctly assembled and stretched.
- An excessive and early stretch of the PINLOCK ® inner visor may result in exces-
sive adherence against the visor surface and/or permanent deformations with
subsequent inability to correctly perform any following adjustments.
- Intense sweating/breathing, the use under particular weather conditions - low
temperatures, high humidity, sudden changes in temperature, heavy rain - or wear
may affect the performance of the PINLOCK ® inner visor and cause fogging or
condensation. In such cases, remove the PINLOCK
®
inner visor from the helmet
visor and let it dry with dry and warm air after use, to restore its performance. The
same procedure should be applied to the helmet in order to dry out humidity in
case it has formed up as a consequence of the conditions described above.
3 PINLOCK
®
INNER VISOR DISASSEMBLY
3.1 Remove the visor with PINLOCK ® inner visor as per instructions above.
3.2 Widen the visor and release the PINLOCK
®
inner visor from its pins (Fig.5).
3.3 Release the visor.
4 MAINTENANCE AND CLEANING
- Remove the PINLOCK ® inner visor from the visor. Using a damp and soft cloth,
gently clean it with neutral liquid soap. Remove the soap under running water.
- Dry the inner visor with dry and warm air without wiping it.
- Let the helmet dry in a ventilated and dry place with the visor open after use. Keep
it away from heat sources and store it in a place away from direct light. This way
inner visor will be kept in good conditions over time.
- Do not use solvents nor chemicals.
REMOVABLE INNER COMFORT PADDING
1
CHEEK PAD DISASSEMBLY
1.1 Unfasten the chin strap (see relevant instructions).
1.2 Pull the front part of the left cheek padding towards the inside of the helmet to
release the three snap fasteners placed on the back (Fig.6).