Nokia 7705 Installation Manual Download | Manualshive

Page: 73 / 84

background image

SAR-Hm and SAR-Hmc Chassis Installation Guide

7705 SAR-Hm and 7705 SAR-Hmc Overview

3HE 17810 AAAA TQZZA

© 2022 Nokia. Nokia Confidential Information

Use subject to agreed restrictions on disclosure and use.

73

3.3.3.2

Outdoor 2G/3G/4G Directional Antenna

The Outdoor 2G/3G/4G directional Antenna (3HE12344AA) features a frequency
range of 698 to 960 MHz and 1710 to 2700 MHz and nominal gain of 6 dBi at 698 to
960 MHz and 8 dBi at 1710 to 2700 MHz. The impedance is 50

Ω

. See

3G/LTE Directional Antenna Specifications

Outdoor 2G/3G/4G Directional

Antenna Installation Overview

for more information.

On the back of the antenna are two N-Type (female) connectors. The antenna is
waterproof, vented, and rated at IP67 for indoor or outdoor use.

The antenna is shipped with a heavy-duty articulating mounting bracket that supports
horizontal polarization, vertical polarization, or a 45

°

diagonal slant. The bracket can

be fixed to a mast measuring 1.63 to 2.3 in. (41.4 to 58.4 mm) O.D. using pipe
clamps. Pipe clamps and installation instructions are included with the antenna.

3.3.3.3

Indoor LTE Omni-directional Antenna

The indoor LTE omni-directional Antenna (3HE12371AA) is a dipole terminal
antenna with a hinged SMA (male) connector suitable for direct mount on the
7705 SAR-Hm in an indoor facility.

The antenna operates in a dual frequency of 698 to 960 MHz and 1710 to 2690 MHz,
a nominal impedance of 50

Ω

. See

Indoor LTE Omni-directional Antenna

and

Direct-mounting the Indoor LTE Omni-directional Antenna

for

more information.

3.3.3.4

LTE Surge Protectors

The LTE surge protectors are designed to offer sufficient protection against lightning
surges and are highly recommended when installing outdoor antennas.

Nokia offers three variants, which are N-Type (female to female) for indoor to outdoor
applications, and N-Type (female to male) or 4.3-10 (male to female) for
7705 Outdoor Enclosure applications. The frequency range is from 698 MHz to
2700 MHz.

«
...
71
72
73
74
75
...
»

Summary of Contents for 7705





















































































Reviews:

No comments

Related manuals for 7705

AirConnect 9550

Brand: 3Com Pages: 68

Brand: Homefibre Pages: 2

Brand: Ubiquiti Pages: 16

Brand: LTE Pages: 8

Brand: Watchguard Pages: 28

Brand: TP-Link Pages: 2

Pepwave Surf SOHO

Brand: peplink Pages: 151

Brand: EliteConnect Pages: 214

Brand: Ebyte Pages: 14

Brand: Zonet Pages: 51

Brand: u-blox Pages: 36

Brand: Comtrol Pages: 36

Brand: Westermo Pages: 29

Brand: Linksys Pages: 104

Brand: Ubiquiti Pages: 9

Brand: Ebyte Pages: 23

Brand: Draytek Pages: 4

Brand: Draytek Pages: 171

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands