manualshive.com logo in svg

Nokia 7705, Installation Manual

Share
Download
Nokia 7705 Installation Manual Download Page 57

SAR-Hm and SAR-Hmc Chassis Installation Guide

Mandatory Regulations

3HE 17810 AAAA TQZZA 

© 2022 Nokia. Nokia Confidential Information

Use subject to agreed restrictions on disclosure and use.

57

 

2.15 Hazardous Locations

2.15.1 Chassis Labels

The 7705 SAR-Hm and 7705 SAR-Hmc chassis display the following labels:

2.15.2 Conditions of Use 

• The equipment shall be installed in an enclosure that provides a degree of 

protection not less than IP 54 in accordance with EN 60079-0 and EN 60079-7. 
Any field wiring connections or cable entries used for this outer enclosure shall 
also be suitably certified against the enclosure requirements of EN 60079-0 and 
EN 60079-7. The installer shall ensure that the maximum ambient temperature 
of the module when installed is not exceeded.

• The equipment shall only be used in an area of at least pollution degree 2, as 

defined in IEC 60664-1.

• The chassis shall be grounded as described in the in this manual before use.
• The SIM card shall be connected or disconnected only in a non-hazardous area 

or when the device is not energized.

• The end-use enclosure shall provide a Warning label “Do not open while 

energized”.

Note: 

See 

7705 Outdoor Enclosure Requirements for Hazardous Locations

 for hazardous 

locations requirements pertaining to the 7705 Outdoor Enclosure.

Summary of Contents for 7705





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands