manualshive.com logo in svg

Nokia 7705, Installation Manual

Share
Download
Nokia 7705 Installation Manual Download Page 79

SAR-Hm and SAR-Hmc Chassis Installation Guide

7705 SAR-Hm and 7705 SAR-Hmc Overview

3HE 17810 AAAA TQZZA 

© 2022 Nokia. Nokia Confidential Information

Use subject to agreed restrictions on disclosure and use.

79

 

3.8 Chassis Installation Process

3.8.1 Preparation

Step 1.

Review all regulations. See 

Mandatory Regulations

.

Step 2.

Assess and prepare the site and observe all safety warnings. See 

Site 

Preparation

.

3.8.2 Pre-staging 

This section applies only if you are using ADP-Hm to initialize and commission the 
7705 SAR-Hm or 7705 SAR-Hmc in a pre-staging facility.

To pre-stage the 7705 SAR-Hm or 7705 SAR-Hmc chassis, perform the following 
steps in order:

Step 1.

Unpack the chassis at the pre-staging facility. See 

Unpacking the Chassis

.

Step 2.

Install the SIM. See 

Installing the SIM

.

Step 3.

Install the chassis on a table top. See 

Mounting the Chassis on a Flat 

Surface

.

Step 4.

Ground the chassis. See 

Grounding the Chassis

.

Step 5.

Connect the antenna and network cables to the chassis. See 

Making 

Indoor Antenna Connections to the 7705 SAR-Hm

 and 

Making 

Connections to the RJ-45 Ports

.

Step 6.

Prepare the DC input power cables and connections to the DC power feed. 
See 

Preparing the DC Power Connections

. If the HV-PS35 is used, see 

High Voltage Power Supply Unit

.

Step 7.

Power up the system and monitor ADP-Hm. See 

Powering Up and 

Initializing

.

Step 8.

Shut down all power to the router. 

Step 9.

Remove the power cables from the router.

Step 10.

Remove the antennas and cabling from the router. Do not remove the SIM.

Note: 

The instructions in this guide assume that the prerequisites for the instantiation of 

ADP-Hm have been completed. Refer to the 7705 SAR-Hm and 7705 SAR-Hmc Main 
Configuration Guide for more information.

Summary of Contents for 7705





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands