manualshive.com logo in svg

Nokia 7705, Installation Manual

Share
Download
Nokia 7705 Installation Manual Download Page 20

Preface

20

SAR-Hm and SAR-Hmc Chassis Installation Guide

© 2022 Nokia. Nokia Confidential Information

Use subject to agreed restrictions on disclosure and use.

3HE 17810 AAAA TQZZA 

 

1.1.4 Information Symbols

Table 1

 describes symbols contained in this guide. 

Table 1

Information Symbols

Symbol

Meaning

Description

Danger

This symbol warns that improper handling and installation could result in bodily 
injury. An electric shock hazard could exist. Before you begin work on this 
equipment, be aware of hazards involving electrical circuitry, be familiar with 
networking environments, and perform accident prevention procedures.

Warning

This symbol warns that improper handling and installation could result in 
equipment damage or loss of data. 

Caution

This symbol warns that improper handling may reduce your component or 
system performance.

Note

This symbol provides additional operational information. 

Summary of Contents for 7705





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands