manualshive.com logo in svg

Nokia 7705, Installation Manual

Share
Download
Nokia 7705 Installation Manual Download Page 72

7705 SAR-Hm and 7705 SAR-Hmc Overview

72

SAR-Hm and SAR-Hmc Chassis Installation Guide

© 2022 Nokia. Nokia Confidential Information

Use subject to agreed restrictions on disclosure and use.

3HE 17810 AAAA TQZZA 

 

See 

Installing the SIM

 for installation instructions. Refer to the 7705 SAR-Hm 

Interface Configuration Guide for more information about SIMs and the configuration 
of the cellular interface.

3.3.3 Commercial Cellular Antennas

Table 12

 lists the commercial cellular antennas that are available from and approved 

by Nokia for use with the 7705 SAR-Hm and 7705 SAR-Hmc.

3.3.3.1

Outdoor 2G/3G/4G Omni-directional Antenna

The Outdoor 2G/3G/4G omni-directional Antenna (3HE12343AA) is a MIMO 
omni-directional LTE antenna that operates at two frequency ranges, 695 to 960 
MHz and 1700 to 2700 MHz with gain of 2 dBi and 3dBi respectively. Impedance is 
50 

Ω

. The antenna is equipped with two N-Type (female) connectors.

Installation instructions, a mounting bracket, U-bolts, and fastening hardware for 
mounting the antenna on a mast up to 2.5 in. (63.5 mm) O.D. are shipped with the 
antenna. See 

Outdoor 2G/3G/LTE Omni-directional Antenna Specifications

 and 

Outdoor 2G/3G/4G Omni-directional Antenna Installation Overview

 for more 

information.

Table 12

Carrier Wireless Commercial Antenna Options 

Nokia Part 
Number

Description

Comments

3HE12343AA

Outdoor 2G/3G/4G omni-directional 
Antenna 

Omni-directional antenna with mounting bracket kit. 
See 

Outdoor 2G/3G/4G Omni-directional Antenna

.

3HE12344AA

Outdoor 2G/3G/4G directional 
Antenna 

Directional antenna with mounting bracket kit. See 

Outdoor 2G/3G/4G Directional Antenna

.

3HE12371AA

Indoor LTE omni-directional Antenna

See 

Indoor LTE Omni-directional Antenna

.

Summary of Contents for 7705





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands