Ningbo SSPP Instruction Manual Download Page 44 | Manualshive

Page: 44 / 44

Ningbo SSPP Instruction Manual Download Page 44

44

SPPE-OM-001
October, 2012

Manufacturer

NINGBO LIHAO MACHINERY CO.,LTD.

Address

NO.408,SONGHUAJIANG ROAD BEILUN,NINGBO 315800

Country CHINA

Type Pole Pruner Attachment
Model SSPP
Serial No. SPPE-1000001 ~

Declare, that the following machinery complies with all the essential health and safety
Requirements of the EC Directive.
2006/42/EC
2004/108/EC
2000/14/EC amended 2005/88/EC

The following standards have been applied
EN ISO 12100:2010
EN ISO 11680-1:2011
EN ISO 14982:2009

Approved Powerhead
UMC425E
UMC435E

Guaranted sound power level (in accordance with 2000/14/EC)
Use with UMC425E 105 dB(A)
Use with UMC435E 107 dB(A)

Issued at: Hiroshi Sugimoto, China
on October 1st 2012
Name and position of the person that signs: Hiroshi Sugimoto
President
Manufacturer’ s signature

Person authorised to complie the technical file
Honda Motor Europe Ltd. Aalst Office
Wijngaardveld 1 (Noord V), 9300 Aalst
BELGIUM

EC Declaration of Conformity

( Applies to Europe only )

«
...
42
43
44

Summary of Contents for SSPP













































Reviews:

No comments