manualshive.com logo in svg

Ningbo SSPP, Instruction Manual, Page: 41 / 44

Share
Download
Ningbo SSPP Instruction Manual Download Page 41

41

7.  Waste Disposal

For disposal, observe the standards and regulations of your region. If there is any question, contact the
sales agency.

8. Troubleshooting

In case of failure, follow the table below.

When troubleshooting, stop the engine and then remove the attachment from  

the powerhead.

*  If the engine starts during the work, hands or fingers could be severed by the moving 

parts or saw chain.

Phenomena

Causes

Measures

The pole pruner 

does not start.

Fuel runs out or fails.

Refuel or replace the fuel by reference to the 

powerhead manual

Engine fails.

Refer to the powerhead manual.

Start/stop switch is off.

Turn on the start/stop switch to start.

Output is not 

enough.

Throttle wire adjustment is faulty. Adjust by referring to the powerhead manual.
Engine fails.

Refer to the powerhead manual.

Saw chain is worn.

Adjust by referring to 5.1.2.

Vibration is too 

large.

Poor balance of attachment

Contact the sales agency.

Mis-installation of attachment

Check the installed status

Connection of Split Attachment is 

loose.

Contact the sales agency.

Saw chain is worn or the tension 

applied is not appropriate.

Adjust by referring to 3.1.1 and 5.1.2.

Shaft tube is bent.

Contact the sales agency.

Exhaust sound is 

too large.

Engine fails.

Refer to the powerhead manual.

Blade is blunt.

Saw chain is worn.

Adjust  by referring to 5.1.2.

Saw chain does 

not stop even if the 

engine speed is 

reduced.

Engine fails.

Refer to the powerhead manual.

Saw chain does 

not move even if 

the engine speed 

is increased.

Split engine  is insufficiently 

inserted into the joint case.

Connect again by referring to 3.2.2.

Shaft tube is broken.

Contact the sales agency.

Failure inside the clutch housing 

of the split engine

Contact the sales agency.

Gear is worn.

Contact the sales agency.

The pole pruner 

does not stop.

Engine fails.

Refer to the powerhead manual.

Summary of Contents for SSPP













































Reviews:

No comments