CARACTERISTIQUES TECHNIQUES
To obtain the optimum performance and
the longest possible life for your high pres-
sure cleaner it is important to maintain the
machine. We recommend that you follow
the following directions and refer to the
check list on the next page.
Oil level/punp
Add oil in level with the lower edge of the
oil filling hole
(for oil type and quantity please see the
technical data).
Water filter
Clean the water filter (2.9) as needed.
Disconnect the water inlet hose and
remove the water filter.
Fuel filter
We recommend that you change the filter
once a year or as the need arises.
If water is found in the fuel filter (4.36)
change the filter. Empty the fuel tank (2.11)
Clean the tank.
Turbo Laser
Clean the filter in the Turbo Laser lance
(2.27) regularly. The filter is mounted in the
inlet opening at the throttle control to pre-
vent particles such as calcium and sand
from entering the Turbo Laser where they
may cause increased wear, leaks or in seri-
ous cases operating malfunctions.
It may be necessary to change the filter. If
so, put a screwdriver or similar tool through
the filter and pull it out. Fit the new filter
with an O-ring and press it into the opening
of the Turbo Laser lance. Make sure that
the filter is placed with the largest contact
face towards the Turbo Laser head.
When inspecting or replacing parts in the
Turbo Laser spray the metal parts
with “Pronto Universal”, "WD 40",
“Servisol”, “Caramba” or similar
products that are able to:
a. Counteract moisture
b. Protect against corrosion
c. Lubricate and clean
We also recommend the above mentioned
treatment if the Turbo lance is not being
used for a long period of time.
Water softener
To prevent lime scale deposits from block-
ing pipes, hoses and nozzles water soften-
er is added to the water which is fed into
the tank (3.32).
Descaling
Even though the high pressure cleaner is
equipped with a water softener device we
recommend that the machine be regularly
descaled. Descaling is required if you find
a pressure increase of 5 bar or more over
operating pressure.
1.
Place the detergent pipe (2.34)
into the descaling acid.
2.
Dismount the lance82.27) from the
pistol (2.26).
3.
Start the cleaner and let it run for
1/2 min.
4.
Close the pistol (2.26) a few times
so the cleaner is also descaled in
the by-pass system.
5.
Stop the cleaner and let the
descaling acid work for 5 min.
6.
Restart the cleaner.
If the pressure is not down to the operating
pressure the process is repeated. After
descaling the system must be with clean
water to remove acid residues. Close the
pistol a couple of times so that the by-pass
system of the cleaner is flushed clean. The
cleaner is then ready for use again.
NOTE!
Descaling acid is corrosive; wear
facial protection, protective gloves,
etc.
Frost protection
The best frost protection is to place
your high pressure cleaner in a
frost free environment. If this is not
possible the high pressure cleaner must
be frost protected as follows:
1.
Remove the cover and turn off the
water supply.
2.
Turn on the machine, activate the
pistol and let the machine empty
the water tank.
3.
Add 4 litres of antifreeze mix. to the
water tank (2.7).
4.
Start the machine by turning the
switch (2.28) to pos. “AUT”, acti-
vate the pistol and let the machine
run with the pressure regulation
handle in the open position until
antifreeze comes out of the noz-
zles (2.1) and (2.2). Release the
pistol trigger a couple of times to
frost protect the by-pass and safe-
ty valve.
The antifreeze can be collected and used
again.
Cleaning
Always keep your high pressure cleaner
clean. This increases the life and function
of the individual parts considerably.
Replacements/destruction
All replaced parts such as water filter, fine
sand filter, Turbo Laser filter as well as con-
taminated oil and antifreeze must be hand-
ed in to the local approved authority/insti-
tution for deposit/destruc-tion.
When the high pressure cleaner is no
longer to be used, the detergent as well as
pump and stator oil must be drained off
and delivered in accordance with the
above mentioned instructions. The high
pressure cleaner must likewise be handed
in to the local, approved institution for
destruction.
Any replaced parts from service visits may
be given to the service personnel who will
deliver them to the proper authority.
31
50
Detergent application
Use only detergent which has been devel-
oped specifically for use in high pressure
cleaners. It is economical in use and is
gentle on the cleaning object and the high
pressure cleaner.
1.
Place the detergent hose with the
detergent filter in the tank contain-
ing detergent. Check that the
detergent covers the filter com-
pletely.
2.
The desired amount of detergent
(up to 6%) can be set on the deter-
gent regulator (2.29).
3.
On the
SPECTRUM
lance and the
Turbo Laser, application of deter-
gents can be carried out by turn-
ing the regulation handle.
After using detergents, clean water should
be sucked through the pump. Place the
detergent hose in clean water, and let the
machine run for a few minutes
MAINTENANCE
TEKNI
2302A
2502A
2702A
Pump pressure
bar/psi
130/1885
140/2000
155/2103
Pump pressure w./steam device
bar
40
40
40
Turbo pressure, ETP
bar/psi
175/2540
185/2683
195/2828
Water quantity at max/min pressure
l/h
440/490
530/580
670/720
Water quantity w./steam device
l/250
250
290
360
Max. temperature with max water qty.
oC
80
80
80
Max. temperature, steam
oC
130
130
130
Detergent dosage
%
0-6
0-6
0-6
Recoil force, max
N
16
20
27
Breaking pressure, by-pass valve
bar
150
150
200
Breaking pressure, safety valve
bar
210
195
210
Pump oil, Type
l
0,11
0,11
0,11
Water connection
"
3/4
3/4
3/4
Inlet pressurMine, max.
bar
1/10
1/10
1/10
Inlet temperature, max
oC
30
30
30
Amp. consumption, 1/240x230V
A
9,5
12,5
-
Amp. consumption, 3x230V
A
-
-
10,5
Amp. consumption, 3x400V
A
-
-
6
Amp. consumption, 3x415V
A
-
-
6
Fuse 1x230V
A
10
13
-
Fuse 3x230V
A
-
-
16
Fuse 3x400V
A
-
-
10
Fuse 3x415V
A
-
-
10
Power consumption
kW
2,2
2,9
3,5
Fuel tank
l
20
20
20
Fuel consumption,
∆
t v. 50°C
l/h
2,1
2,4
2,85
Burner nozzle
gal./o
0,65/80H
0,85/80H
1,1/80H
Heating effect
kW
30
36
46
Double lance high pressure nozzle
dim.
1503,0
1503,5
1504,0
Double lance low pressure nozzle
dim.
4040
4040
4040
Double lance nozzle angles
o
15/40
15/40
15/40
130
135
140
Electric cable
m
4,5
4,5
4,5
High pressure hose, DN-size
mm
8
8
8
High pressure hose, lenght
m
10
10
10
Weight
kg
72
73
73
Depth
mm
535
535
535
Wiht
mm
585
585
585
Height
mm
780
780
780
Noise level (ISO 3746)
dB(A)
84/97
84/97
85/100
Modèle
Pression de pompe
bar/psi
(Pression de pompe, étage vapeur)**
bar
Pression du Turbo,
ETP-bar/psi
Débit d’eau à la pression min
l/h
(Débit d’eau avec étage vapeur)**
l/h
Température, Max
°C
(Température avec étage vapeur, Max.)**
°C
Dosage détergent HP
%
Force de recul à la pression max.
N
Pression vanne by-pass
bar
Pression vanne sécurité
bar
Huile pour pompe SAE 10W/40
l
Raccordement eau
”
Pression min./max. de l’eau d’admission bar
Température max. de l’eau d’admission
°C
Intensité en 1 X 230/240V, 50/60Hz
A
Intensité en 3 X 230V, 50Hz
A
Intensité en 3 X 400V, 50Hz
A
Intensité en 3 X 415V, 50Hz
A
Fusible 1 X 230/240V, 50/60 Hz
A
Fusible 3 X 230V, 50 Hz
A
Fusible 3 X 400V, 50 Hz
A
Fusible 3 X 415V, 50 Hz
A
Puissance consommée
kW
Réservoir de gas-oil
l
Consommation de gas-oil,
∆
t v. 50°C
l/h
Gicleur à gas-oil
usg/°
Rendement thermique
kW
Gicleur HP pour Lance double
taille
Gicleur BP pour Lance double
taille
Coudes de gicleur, lance double
°
Spectrum
dim
Câble électrique
m
Tuyau haute pression
Ømm
Tuyau haute pression
m
Poids
kg
Longueur
mm
Largeur
mm
Hauteur
mm
Niveau sonore
dB(A)
( )** Option
