6
6
6
6
6 - FORM NO. 56043089 / AquaRide
™
/ BRX 700
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE
Maintenance intervals given are for average operating conditions. Machines used in severe operational environments may require
service more often.
MAINTENANCE ITEM
MAINTENANCE ITEM
MAINTENANCE ITEM
MAINTENANCE ITEM
MAINTENANCE ITEM
Daily
Daily
Daily
Daily
Daily
Weekly
Weekly
Weekly
Weekly
Weekly
Monthly
Monthly
Monthly
Monthly
Monthly
Yearly
Yearly
Yearly
Yearly
Yearly
Charge Batteries
•
Check/Clean Tanks & Hoses
•
Check/Clean/ Power Brush(s)
•
Check/Clean Vacuum Shoes
•
Check/Clean Vacuum Shut-Off Float
•
Check/Clean the vacuum motor foam filter(s)
•
Empty Debris Hopper (sweeping model)
•
Clean Spray Nozzles
•
Check Each Battery Cell(s) Water Level
•
Inspect Brush Deck Skirts
•
Inspect and clean Solution Filter
•
Check Foot/ Parking Brake for Wear & Adjustment
•
Lubrication - Grease Fittings
•
* Check Carbon Brushes
•
Note: See the individual machine system sections for maintenance information.
* Have Nilfisk-Advance:
Check vacuum motor carbon brushes (Qty 2) once a year or after 300 operating hours.
Check brush motor carbon brushes (Qty 4) once a year or after 500 operating hours.
Note if the vacuum or brush motor brushes are 9.5mm (3/8 inches) or shorter, replace them.
Check wheel drive motor carbon brushes every 500 operating hours. The original length of each brush is 20mm (25/32 inches).
Replace when shorter than 9.5 mm (3/8 inches) to obtain the same motor efficiency as a new brush.
WARNING!
WARNING!
WARNING!
WARNING!
WARNING!
Turn the key switch off, set the parking brake and disconnect the battery before servicing the machine.
VACUUM SHOE MAINTENANCE
VACUUM SHOE MAINTENANCE
VACUUM SHOE MAINTENANCE
VACUUM SHOE MAINTENANCE
VACUUM SHOE MAINTENANCE
Check the vacuum shoes daily, they can be removed to aid in cleaning, see “Removing the Vacuum Shoes”. Remove any built-up
string, hair or carpet fibers.
SPRA
SPRA
SPRA
SPRA
SPRAY NOZZLE MAINTENANCE
Y NOZZLE MAINTENANCE
Y NOZZLE MAINTENANCE
Y NOZZLE MAINTENANCE
Y NOZZLE MAINTENANCE
Remove the spray nozzles once a week. Soak the nozzles overnight in a vinegar solution to remove chemical deposits.
LUBRICA
LUBRICA
LUBRICA
LUBRICA
LUBRICATING THE MACHINE
TING THE MACHINE
TING THE MACHINE
TING THE MACHINE
TING THE MACHINE
Once a month, pump a small amount of grease into each grease fitting on the machine until grease seeps out around the bearings.
Grease fitting locations are:
Grease fitting locations are:
Grease fitting locations are:
Grease fitting locations are:
Grease fitting locations are:
•
Steering Wheel Shaft Universal joint
Once a month, apply light machine oil to lubricate the:
Once a month, apply light machine oil to lubricate the:
Once a month, apply light machine oil to lubricate the:
Once a month, apply light machine oil to lubricate the:
Once a month, apply light machine oil to lubricate the:
•
Steering Chain
•
General Pivot Points For the Brush Deck Linkage
•
Scrub Deck Adjustment Knobs (4)
CLEANING THE V
CLEANING THE V
CLEANING THE V
CLEANING THE V
CLEANING THE VACUUM MOTOR FIL
ACUUM MOTOR FIL
ACUUM MOTOR FIL
ACUUM MOTOR FIL
ACUUM MOTOR FILTERS
TERS
TERS
TERS
TERS
Clean the vacuum motor filters daily with compressed air. For extremely dirty filters, wash with warm, soapy water and rinse
thoroughly with clean water. Allow the filters to dry completely before re-installing in the machine. MAINTENANCE NOTE: Keep a
second set of filters on hand to use while first set is drying.
POWER BRUSH MAINTENANCE
POWER BRUSH MAINTENANCE
POWER BRUSH MAINTENANCE
POWER BRUSH MAINTENANCE
POWER BRUSH MAINTENANCE
Check the brush(s) daily. Remove any built-up string, hair or carpet fibers. Check the bristle length. Have a service technician change the brush(s)
when the brush bristles are worn to 1 inch (25mm).
MAINTENANCE
MAINTENANCE
MAINTENANCE
MAINTENANCE
MAINTENANCE