Nilfisk-Advance AquaRide BRX 700, Service Manual, Page: 76 / 82

74 74 74 74 74 - FORM NO. 56043089 / AquaRide ™ / BRX 700
ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM
Single or Dual Vacuum Motor Selection: Single or Dual Vacuum Motor Selection:
Single or Dual Vacuum Motor Selection: Single or Dual Vacuum Motor Selection: Single or Dual Vacuum Motor Selection:
FACTORY DEFAULT: 2 (DUAL VACUUM MOTORS)
The AquaRide comes with standard dual vacuum motors. If for some reason it is desired to use only one vacuum motor, the control
must be programmed accordingly to provide the proper overcurrent protection for the vacuum motor. To program the control for
the number of vacuum motors perform the following steps:
1 Turn the main power key switch
main power key switch
main power key switch main power key switch main power key switch to the off
off
off off off position.
2 Press and hold the scrub system off
scrub system off
scrub system off scrub system off scrub system off and vacuum switches
vacuum switches
vacuum switches vacuum switches vacuum switches.
3 While holding both switches turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the on on on on on position.
4 Continue to hold both switches until the vacuum indicator is yellow.
5 Release both switches. The status display will now indicate “1” or “2”.
6 Pressing and releasing the vacuum vacuum vacuum vacuum vacuum switch will now select between “1” for a single vacuum motor or “2” for dual vacuum motors.
7 To save the new setting turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the off off off off off position.
8 The new setting will be saved and will remain in effect until it is changed again.
Control Unit Sleep Delay Period: Control Unit Sleep Delay Period: Control Unit Sleep Delay Period: Control Unit Sleep Delay Period: Control Unit Sleep Delay Period:
FACTORY DEFAULT: 1 (10 MINUTES)
If the AquaRide is left in an idle state for a period determined by the sleep delay setting the control unit will automatically raise the
scrub deck and turn off any accessories. This is to conserve battery power. The sleep period is adjustable from 10 to 90 minutes
in 10 minute increments. It can also be turned off. To change the sleep delay period perform the following steps:
1 Turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the off off off off off position.
2 Press and hold the scrub system off scrub system off
scrub system off scrub system off
scrub system off and the wand switch. wand switch.
wand switch. wand switch.
wand switch.
3 While holding both switches turn the main power key switch main power key switch
main power key switch main power key switch
main power key switch to the on on
on on
on position.
4 Continue to hold both switches until the wand indicator is flashing.
5 Release both switches. The status display will now indicate a number from 0 to 9 depending on the current sleep delay period.
6 Pressing and releasing the wand switch wand switch wand switch wand switch wand switch will now select the delay period. The level will increment from 0 to 9; 0 = off (sleep
disabled), 1 = 10 minutes, 2 = 20 minutes, ... up to 9 = 90 minutes.
7 To save the new setting, turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the off off off off off position.
8 The new setting will be saved and will remain in effect until it is changed again.
Turning the Extract Deck Raise-In-Reverse Option On or Off: Turning the Extract Deck Raise-In-Reverse Option On or Off: Turning the Extract Deck Raise-In-Reverse Option On or Off: Turning the Extract Deck Raise-In-Reverse Option On or Off: Turning the Extract Deck Raise-In-Reverse Option On or Off:
FACTORY DEFAULT: ON
To prevent chattering of the extractor pick-up shoes while backing up, the scrub deck will automatically raise to the up position.
If it is desired to allow the scrub deck to remain down while backing up, this option may be turned off. To turn this option on or off,
perform the following steps:
1 Turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the off off off off off position.
2 Press and hold the scrub system off scrub system off scrub system off scrub system off scrub system off and maintenance mode switches maintenance mode switches maintenance mode switches maintenance mode switches maintenance mode switches.
3 While holding both switches turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the on on on on on position.
4 Continue to hold both switches until the maintenance mode indicator is yellow.
5 Release both switches. The status display will now indicate “E” or “d”.
6 Pressing and releasing the maintenance mode maintenance mode
maintenance mode maintenance mode
maintenance mode switch will now select between “E” for enabled or “d” for disabled. Enabled
means that the option is turned on (deck will rise in reverse), disabled means that the option is turned off (deck will stay down
in reverse).
7 To save the new setting, turn the main power key switch
main power key switch
main power key switch main power key switch main power key switch to the off
off
off off off position.
8 The new setting will be saved and will remain in effect until it is changed again.
SPECIAL PROGRAM OPTIONS (CONTINUED) SPECIAL PROGRAM OPTIONS (CONTINUED)
SPECIAL PROGRAM OPTIONS (CONTINUED) SPECIAL PROGRAM OPTIONS (CONTINUED)
SPECIAL PROGRAM OPTIONS (CONTINUED)