FORM NO. 56043129 - SR 1900 -
11
MAINTENANCE
IMPORTANT MACHINE LUBRICATION
Rear Steering Yoke Bearing Assembly
Once every 150 hours attach a grease gun to the yoke bearing pivot zert (location under operator’s seat) and pump a small amount of grease into
bearing assembly.
Also every 150 hours apply light machine oil to maintain free movement of all general pivot points. Example the seat, and broom door hinges etc.
Broom and hopper pivots use composite bearings lubrication is not required.
WARNING
For the protection of the environment; when servicing any of the machine’s lubrication fluids they must be disposed of safely in accordance with
your local environmental regulations (recycling). Examples of machine lubrication products:
(Engine crankcase oil, Engine crankcase oil filter,
Hydraulic system oil, Hydraulic system oil filters).
ENGINE COOLANT
CAUTION!
Do not remove the radiator cap when the engine is hot.
To check the engine coolant level, first unlatch and open the Oil Reservoir / Fuel Tank Cover
(20)
then lift the Engine Compartment Cover
(1)
and
observe the coolant level on the Coolant Recovery Tank
(15)
or
(22)
. If the level is low add a mixture of half water and automotive type anti-freeze.
Clean the radiator and oil cooler exteriors by washing with low-pressure water or using compressed air every 30 hours. Service Note: The oil cooler
tips out for easy cleaning.
ENGINE OIL – GASOLINE (PETROL) & LPG
Check the engine oil level when the machine is parked on a level surface and the engine is cool. Change the engine oil after the first 35 hours of
operation and every 150 hours after that. Use any SF or SG rated oil meeting API specifications and suited to seasonal temperatures. Refer to the
Engine System section for oil capacities and additional engine specifications. Replace the oil filter with every oil change.
TEMPERATURE RANGE
OIL WEIGHT
Above 60° F (15° C)
SAE 10W-30
Below 60° F (15° C)
SAE 5W-30
ENGINE OIL - DIESEL
Check the engine oil level when the machine is parked on a level surface and the engine is cool. Change the engine oil after the first 35 hours
of operation and every 150 hours after that. Use CF, CF-4 or CG-4 oil meeting API specifications and suited temperatures (*important reference
the oil/fuel type note below for further diesel oil recommendations). Refer to the Engine System section for oil capacities and additional engine
specifications. Replace the oil filter with every oil change.
TEMPERATURE RANGE
OIL WEIGHT
Above 77 °F (25 °C)
SAE 30 or 10W-30
32 °F to 77 °F (0 °C to 25 °C)
SAE 20 or 10W-30
Below 32 °F (0 °C)
SAE 10W or 10W-30
* Diesel Lubricating Oil Note:
With the emission control now in effect, the CF-4 and CG-4 lubricating oils have been developed for use of a low-sulfur fuel on-road vehicle
engines. When an off-road vehicle engine runs on a high-sulfur fuel, it is advisable to employ the CF, CD or CE lubricating oil with a high total
base number. If the CF-4 or CG-4 lubricating oil is used with a high-sulfur fuel, change the lubricating oil at shorter intervals.
• Lubricating oil recommended when a low-sulfur or high-sulfur fuel is employed.
Fuel
Lubricating
Oil class
Low sulfur
(0.5 % ≥)
High sulfur
Remarks
CF
O
O
TBN ≥ 10
CF-4
O
X
CG-4
O
X
O
: Recommendable
X
: Not recommendable
Summary of Contents for 56507009
Page 5: ...FORM NO 56043129 SR 1900 5...
Page 64: ...64 FORM NO 56043129 SR 1900 THIS PAGE IS INTENTIONALLY BLANK...
Page 76: ...76 FORM NO 56043129 SR 1900 ENGINE HARNESS FOR GM 1 6L GAS Petrol Tier 3 ELECTRICAL SYSTEM...
Page 77: ...FORM NO 56043129 SR 1900 77 ELECTRICAL SYSTEM ENGINE HARNESS FOR GM 1 6L LPG Tier 3...
