background image

410-00362

EN

12

3.  TROUBLESHOOTING

If the wireless system according to the Easywave protocol does not work after programming, a number of extra checks can be carried out first:
• Check the operation of the connected transmitter. Press the programming button at the front of the transmitter. If the indication LED does not flash, the 

transmitter is faulty.

• Check the wireless signal strength in the environment using a diagnostics device (05-370). If the reach is insufficient, move the transmitter or use a wireless 

repeater according to the Easywave protocol (05-535) to increase the range.

• Check – in the case of an existing installation – if the environment of the wireless system has changed, causing disruptions (metal electrical cabinet, partitions, 

moved furniture ...). Restore the original situation, if possible.

4.  TECHNICAL DATA 

dimensions

25 x 48 x 48 mm (HxWxD)

weight

32 g

frequency

868.3 MHz

modulation

FSK

power supply voltage

230 Vac, 50 Hz

maximum consumption

0.43 W

range

approximately 100 m in open spaces

protection degree

IP 20

operating temperature

-20 °C - +60 °C

maximum radio frequency 

power of the Easywave signal

3,4 dBm

5.  WARNINGS REGARDING INSTALLATION

• The installation should be carried out by a registered installer and in compliance with the statutory regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file, and it should be passed on to any new owners. Additional 

copies are available on the Niko website or via the Niko support service.

• During installation, the following should be taken into account (non-exhaustive list):

 

- the statutory laws, standards and regulations.

 

- the technology currently available at the time of installation.

 

- this user manual, which only states general regulations and should therefore be read within the scope of each specific installation.

 

- the rules of proper workmanship.

  

This product complies with all of the relevant European guidelines and regulations. If applicable, you can find the EU declaration of conformity regarding this 

product at www.niko.eu.

6.  NIKO SUPPORT

In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support service in Belgium at +32 3 778 90 80 or your 

wholesaler/installer. Contact details and more information can be found at www.niko.eu under the “Help and advice” section.

7.  GUARANTEE PROVISIONS

• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase of the product by the consumer. If there is 

no invoice, the date of production applies.

• The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge, which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless use, incorrect operation, transformation of the 

product, maintenance that does not adhere to the maintenance instructions or an external cause, such as damage due to moisture or overvoltage.

• The compulsory regulations of the national legislation concerning the sale of consumer goods and the protection of the consumer in the countries where Niko 

sells, directly or via sister companies, subsidiaries, chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned 
rules and regulations.

Hereby, Niko nv declares that the radio equipment type 410-00362 is in compliance with Directive 1999/5/EC and Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at www.niko.eu.

Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point. Together with producers and importers, you have an important role to play in 
the advancement of sorting, recycling and reusing discarded electrical and electronic appliances. In order to finance the waste collection and processing, the government levies 
a recycling contribution in some cases (included in the purchase price of this product).

Summary of Contents for 410-00362

















Reviews: