background image

360-45012

EN nv 

Niko

 sa    Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: [email protected] — www.niko.eu 

PM360-45012R12412

Reset units

Resets the parameters (

Fade factor

,

 Power on

,

 Failure LVL

) and deletes the zone assignments. Applicable to 

all light fittings on the DALI bus.

Randomize ID

Deletes the ID addresses and resets all parameters of the selected light fittings to the factory settings.

Randomize units

Deletes the ID addresses and resets all parameters of all light fittings on the DALI bus to the factory settings.

8. WARNINGS REGARDING INSTALLATION

 -The installation should be carried out by a registered installer and in compliance with the statutory regulations.
 -This user manual should be presented to the user. It should be included in the electrical installation file, and 

it should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko 
support service.

 -During installation, the following should be taken into account (non-exhaustive list):

 

- the statutory laws, standards and regulations.

 

- the technology currently available at the time of installation.

 

- this user manual, which only states general regulations and should therefore be read within the scope of 

each specific installation.

 

- the rules of proper workmanship.

  

This product complies with all of the relevant European guidelines and regulations. If applicable, you can find 

the EC declaration of conformity regarding this product at www.niko.eu.

9. NIKO SUPPORT

In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support 

service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can 

be found at www.niko.eu under the “Help and advice” section.

10. GUARANTEE PROVISIONS

 -The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of 

purchase of the product by the consumer. If there is no invoice, the date of production applies.

 -The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating 

the defect.

 -In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge, 

which shall be decided by Niko.

 -Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless 

use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance 
instructions or an external cause, such as damage due to moisture or overvoltage.

 -The compulsory regulations of the national legislation concerning the sale of consumer goods and the 

protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries, 
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned 
rules and regulations.

Summary of Contents for 360-45012


























Reviews: