Nidek Medical RT-5100 Operator'S Manual Download Page 244

Page: 244 / 306

226

21 Point Exams (only for Plus Package)



Standard accommodation power display

According to the “Standard accommodation power display” parameter, the maximum value, average

value, and minimum value calculated by the Morgan’s criterion or Hofstetter formula can be displayed

on the accommodation measurement window. To display this value, patient’s age must be entered

beforehand. For details, see "3.11 Age Input" (Page 118).

Specify the accommodation power to be displayed with the “Standard accommodation display”
parameter.



When the “Standard accommodation power display” parameter is set to
“Morgan”

Displays the range of Morgan’s criterion calculated by age.

Morgan’s criterion
accommodation power

When the accommodation power is below the range of criterion, or the value is 0(D), the accom-

modation power is displayed in pink.



When the “Standard accommodation power display” parameter is set to “Hof-
stetter”

Displays the minimum value, average value, and maximum value calculated by Hofstetter formula.

Minimum value,

average value,
maximum value

When the accommodation power (D) is below the minimum value, or the value is 0(D), the accom-

modation power is displayed in pink.

161221687130 承認済

Uncontrolled copy when printed.

Summary of Contents for RT-5100



















































































































































































































































































































Search results

Summary of Contents for RT-5100

Reviews:

Related manuals for RT-5100

Brands by name

Popular brands

Nidek Medical RT-5100, Operator'S Manual

Search results

Summary of Contents for RT-5100

Reviews:

Related manuals for RT-5100

Brands by name

Popular brands