Nidek Medical RT-5100 Operator'S Manual Download Page 108

Page: 108 / 306

OPERATING PROCEDURE

Printing

2.8.1

Printing with QR code

The final data (subjective or prescription data) is printed as a QR code.

• If paper is rounded, QR code may not be identified. Smooth out paper before reading.

• For details of printed QR code, ask NIDEK or your authorized distributor for the QR code

manual in which the specifications is described.



When the “QR code” parameter is set to “QR1”, the final data and the QR code are
printed. See Figure1.

Figure 1

161221687130 承認済

Uncontrolled copy when printed.

Summary of Contents for RT-5100



















































































































































































































































































































Search results

Summary of Contents for RT-5100

Reviews:

Related manuals for RT-5100

Brands by name

Popular brands

Nidek Medical RT-5100, Operator'S Manual

Search results

Summary of Contents for RT-5100

Reviews:

Related manuals for RT-5100

Brands by name

Popular brands