manualshive.com logo in svg

Nidek Medical RT-5100, Operator'S Manual

Share
Download
Nidek Medical RT-5100 Operator'S Manual Download Page 228

210

21 Point Exams (only for Plus Package)

21 Point Exams (only for Plus Package)

5.2

21 Point Exams (only for Plus Package)

The RT-5100 assigns the subjective (far) value to #7.
The initial value for the subjective (near) value is the subjective (far) value + ADD value.
The RT-5100 indicates the name of exam simply.
The indication and contents of exam on the RT-5100 are as follows:

Exam No.

Indication on

the RT-5100

Contents of measurement

#7

Subj(F)

Perform subjective measurement and obtain the full 

corrective power.

#8

H.Phoria(F)

Far horizontal phoria measurement

#9,10

Conv(F)

Far convergence power measurement

#11

Div(F)

Far divergence power measurement

#12A

V.Phoria(F)

Far vertical phoria measurement

#12B

Supra(F)

Far supravergence power measurement

Infra(F)

Far infravergence power measurement

#13B

H.Phoria(N)

Near horizontal phoria measurement

#14A

C.Cyl(Mon)

Monocular accommodative lag measurement using 

cross cylinder

#14B

C.Cyl(Bin)

Binocular accommodative lag measurement using 

cross cylinder

#15A

H.Phoria(#14A)

Near horizontal phoria measurement using monocular 

accommodative lag (#14A)

#15B

H.Phoria(#14B)

Near horizontal phoria measurement using binocular 

accommodative lag (#14B)

#16

Conv(N)

Near convergence power measurement

#17

Div(N)

Near divergence power measurement

#18A

V.Phoria(N)

Near vertical phoria measurement

#18B

Supra(N)

Near supravergence power measurement

Infra(N)

Near infravergence power measurement

#19

(-)lens

Accommodation measurement with the addition of 

minus lens

NPA

Measurement of near point of accommodation

#20

PRA

Positive relative accommodation measurement

#21

NRA

Negative relative accommodation measurement

• For #13B to #21 exams, set the working distance (WD) to 40 cm.

When the working distance is other than 40 cm, proper analysis cannot be obtained.

161221687130 承認済

Uncontrolled copy when printed.

Summary of Contents for RT-5100



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands