COMMAND CONFIGURATION
This item covers the command categories associable with inputs 1 - 2 - 3 (refer to the section “input configuration - Table 1” to check the commands avail-
able). Each command category features various operating modes as described in a table (1-A, 1-B, etc.):
Step-by-step
In this command category the user can select one of the operating modes specified in Table 1-A.
TABLE 1-A: COMMAND CONFIGURATION
MODE
DESCRIPTION
Industrial mode
This runs the sequence “open in semiautomatic- close in hold-to-run”.
Open - stop - close - stop
This executes the above sequence.
Open - Stop - Close - Open
Operating mode set in factory (Input 1 - “step-by-step” command). This executes the above sequence.
Open - Close - Open - Close
This executes the above sequence.
Apartment block 1 step-by-step
Runs the sequence “close - stop - open - open”, until it reaches the fully open position. Note – If another command
is sent after this one, the application executes the Closing manoeuvre with the same sequence.
Apartment block 2 step-by-step
Runs the sequence “close - stop - open - open” until the fully open position is reached. Note – If another command
is sent after this one, the application executes the Closing manoeuvre with the same sequence. Important – When
sending a command, if the transmitter key is held down for more than 2 seconds, the control unit activates a Stop.
Step-by-step 2
This executes the sequence “open - stop - close - open”. Important – When sending a command, if the transmitter
key is held down for more than 2 seconds, the control unit activates a “partial open 1” command (input configura-
tion > Table 1).
Hold-to-run
The Opening or Closing manoeuvre is executed exclusively if the transmitter key is held down (hold-to-run).
partial open
In this command category the user can select one of the operating modes specified in Table 1-B.
TABLE 1-B: COMMAND CONFIGURATION
MODE
DESCRIPTION
Open - stop - close - stop
Operating mode set in factory. This executes the above sequence.
Open - Stop - Close - Open
This executes the above sequence.
Open - Close - Open - Close
This executes the above sequence.
Apartment block 1 step-by-step
This executes the sequence “close - stop - partial open 1- partial open 1” until the position is reached as pro-
grammed in the function “Partial Open 1”. Note – If another command is sent after this one, the application executes
the Closing manoeuvre with the same sequence.
Apartment block 2 step-by-step
This executes the sequence “close - stop - partial open 1 - partial open 1” until the position is reached as pro-
grammed in the function “Partial Open 1”. Note – If another command is sent after this one, the application executes
the Closing manoeuvre with the same sequence. Important – When sending a command, if the transmitter key is
held down for more than 2 seconds, the control unit activates a Stop.
Hold-to-run
The Partial open 1 or Closing manoeuvre is executed exclusively if the transmitter key is held down (hold-to-run).
Industrial mode
This runs the sequence “open in semiautomatic- close in hold-to-run”.
Open
In this command category the user can select one of the operating modes specified in Table 1-C.
TABLE 1-C: COMMAND CONFIGURATION
MODE
DESCRIPTION
Open - Stop - Open
Operating mode set in factory (Input 2 - “open” command). This executes the above sequence.
Apartment block 1
An Opening manoeuvre is executed.
Apartment block 2
This executes the sequence “open - open”. Important – When sending a command, if the transmitter key is held
down for more than 2 seconds, the control unit activates a Stop.
Open 2
Important – When sending a command, if the transmitter key is held down for more than 2 seconds, the control unit
activates a “partial open 1” command (input configuration > Table 1).
Hold-to-run Open
The Opening manoeuvre is executed exclusively if the transmitter key is held down (hold-to-run).
Close
In this command category the user can select one of the operating modes specified in Table 1-D.
TABLE 1-D: COMMAND CONFIGURATION
MODE
DESCRIPTION
Close - stop - close
Operating mode set in factory (Input 3 - “close” command). This executes the sequence as described.
Apartment block 1 close
This executes the sequence “close - close”.
Apartment block 2 close
This executes the sequence “close - close”. Important – When sending a command, if the transmitter key is held
down for more than 2 seconds, the control unit activates a Stop.
Hold-to-run close
The Closing manoeuvre is executed exclusively if the hold-to-run command is used.
Stop
In this category, you can choose one of the operating modes listed in table 1-E.
TABLE 1-E: COMMAND CONFIGURATION
MODE
DESCRIPTION
Stop
Operating mode set in factory. When the control unit receives the command, it stops the manoeuvre in progress
gradually and in a short time (not instantly).
