background image

Safety instructions and usage guide for the automatic pool cover  - 6/8

6

This document is the property of AS POOL - of the NextPool group and cannot be reproduced or communicated without our authorisation.

5.  Maintenance advice 

wintering advice

Wintering advice is described below, however, it is 
the installer's responsibility to recommend a solution 
depending on the availability of the customer and the 
geographical location of the pool

.

•  Carry out active wintering by operating the circulation 

of the water and fi ltering during the coldest moments of 
the day (An anti-freeze thermostat can trigger fi ltering as 
soon as the air temperature falls below 0°).

•  Keep the water level normal, excess water will drain from 

the overfl ow.

•  Clean the blades unrolled on the pool water using a 

high pressure cleaner and then sweep the pool and the 
storage trench. Treat the water with wintering products.

•  Keep your cover unrolled in the pool and, if the pool is 

surrounded by a lot of vegetation, fi t a netting, permeable 
cover over it in order to avoid the decay of leaves and 
other vegetable debris on the PVC covers. Do not store 
the cover rolled with an accumulation of leaves or debris 
which would trigger an irremediable decaying process 
causing incrusted stains to form on the PVC blades. This 
physical phenomenon is not covered by the warranty for 
the blades.

•  Protect the skimmers and piping exposed to freezing.

•  Protect the motors from fl ooding.

•  Cut the power supply to the electric box. 

•  Do not operate or touch the blades when they are ice 

bound. If there is a risk of the pool icing over, have the 
immersed axis and the roller motor removed.

•  For models using solar power, the batteries can 

remain in place if the solar panel is not covered and 
continues its charging function. If the panel is covered 
and can lo longer charge using sunlight, the batteries 
must be disconnected and stored in a dry place. When 
recommissioning, let the batteries charge (a half day of 
sunlight) before operating the cover. 

6. Guarantee

Our one year guarantee only covers the replacement or 
the repair of a defective part as well as all defects or faults 
in the context of the installation, use, maintenance and 
wintering in compliance with our instructions.

It only comes into effect on the shipping date if the 
reseller or installer returns us the defective parts postage 
paid for analysis.

The guarantee covers all of the electrical equipment 
providing that the wiring was carried out in accordance 
with our instructions and in compliance with the standard 
C 15.100.

The guarantee does not cover the immersion of motors 
not designed for this purpose and the consequences of 
lightning caused by storms.

Apart from the general one-year guarantee, we grant the 
following guarantees:

-  sending a guarantee form duly completed within 8 

days of the cover's installation, gives the right to an 
extension of the geared motor guarantee from 1 to 3 
years free of charge. 

- the roller mechanism: 3 years (1)

- the PVC cover blades: 3 years (2)

- Solar panel: 10 years

- batteries: 1 year.

(1) The guarantee covers the resistance of the used 
materials except to corrosion and the deterioration of 
certain materials due to the use of an appliance producing 
and electro-chemical or electro-physical reaction, which 
generally accelerates the corrosion of metals.  

(2) The guarantee covers the buoyancy, water tightness 
and articulation of the blades. The guarantee does not 
cover brownish stains and discolouration of the blades. 
Distortion of the blue translucent solar blades caused 
by use in disregard of our technical recommendations 
is also excluded. Damage caused by hail is excluded. 
All modifi cations to a blade voids the guarantee on the 
cover.

Are excluded all labour costs for removal, assembly, 
travel, water supply, products, damages and interests as 
well as any claims for compensation for any cause.

Summary of Contents for ABRIBLUE MANU





















Reviews: