Nexo PS Series User Manual Download Page 32

Page: 32 / 82

Page 32/82

ERIES HARDWARE SETUP PROCEDURE

7.3 PS Series in fixed installations

7.3.1 Fixed installation Accessories and kits

Accessories are:



“U” Bracket for PS8 (VNI-UBRK8)



“U” Bracket for PS10R2 (VNI-UBRK10)



“U” Bracket for PS15R2 (VNI-UBRK12)



“L” Bracket for cable suspension for PS10R2 and PS15R2 (VNI-LBRK)



Bracket for ceiling suspension for PS10R2 and PS15R2 (VNI-ABRK)



Wall suspension system for PS8 and PS10R2 (VNI-WS10)



Wall suspension system for PS15R2 (VNI-WS15)

Please refer to section 9.6 of this manual for more information of above references.

IMPORTANT

In order to prevent screws from getting loose in fixed installations, use blocking liquid
LOCTITE

243 or equivalent for all screws used with PS Series fixed installation

accessories.
LOCTITE

243 is available at NEXO or at your local distributor upon request.

VNI-UBRK8

VNI-UBRK10

VNI-UBRK12

VNI-LBRK

VNI-ABRK

VNI-WS10

VNI-WS15

Summary of Contents for PS Series



















































































Search results

Summary of Contents for PS Series

Reviews:

Related manuals for PS Series

Brands by name

Popular brands

Nexo PS Series, User Manual

Search results

Summary of Contents for PS Series

Reviews:

Related manuals for PS Series

Brands by name

Popular brands